WINDOW / GLASS REAR SIDE WINDOW GLASS(except Wagon) REMOVAL
CAUTION / NOTICE / HINT
- NOTICE:
-
Make sure to use Toyota Genuine Windshield Glass Adhesive (High Modulus Type) or equivalent.
- HINT:
- ·
Use the same procedure for RHD and LHD vehicles.
·The procedure listed below is for LHD vehicles.
·Use the same procedure for the RH and LH sides.
·The procedure listed below is for the LH side.
·The No. 2 emergency hammer caution label (Type B) is only on the LH side.
PROCEDURE
1.REMOVE REAR SEAT ASSEMBLY LH
for Commuter, 3-Passenger Seat with 2-Point Type Seat Belt and Headrest:
for Commuter, 3-Passenger Seat with 2-Point Type Seat Belt without Headrest:
for Commuter, 3-Passenger Seat with 3-Point Type Seat Belt:
for Commuter, 4-Passenger Seat:
for Commuter, Single-Passenger Seat with 2-Point Type Seat Belt:
for Commuter, Single-Passenger Seat with 3-Point Type Seat Belt:
for Commuter, 2-Passenger Seat with 3-Point Type Seat Belt:
for Commuter, 2-Passenger Seat with 2-Point Type Seat Belt and Headrest:
for Commuter, 2-Passenger Seat with 2-Point Type Seat Belt without Headrest:
67918D
2.REMOVE REAR DOOR SCUFF PLATE LH
67872A
3.REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP LH (for Full-trim, for High Roof, w/ Rear Door)
- HINT:
-
Use the same procedure for the quarter pillar garnish RH.
73233
4.REMOVE OUTER LAP BELT ANCHOR COVER (for Full-trim)
73220
5.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR) (for Full-trim)
73370E
6.REMOVE REAR SEAT OUTER BELT ASSEMBLY LH (for Full-trim, w/ Seat Belt)
58777A
7.REMOVE TOOL BAG HOLDER (for Full-trim)
67935
8.REMOVE BACK DOOR SCUFF PLATE (for Full-trim)
62640M
9.REMOVE REAR QUARTER TRIM BOARD ASSEMBLY LH (for Full-trim, for High Roof)
62620K
10.REMOVE SIDE TRIM BOARD ASSEMBLY LH (for Full-trim, for High Roof)
62472D
11.REMOVE REAR UPPER PILLAR GARNISH LH (for Full-trim)
74733
12.REMOVE NO. 1 HAND GRIP COVER (for Full-trim, w/ Hand Rail)
74708
13.REMOVE NO. 2 HAND GRIP FRAME SUB-ASSEMBLY (for Full-trim, w/ Hand Rail)
62639A
14.REMOVE QUARTER PILLAR GARNISH LH (for Full-trim)
62639A
15.REMOVE QUARTER PILLAR GARNISH LH (for Full-trim, for High Roof)
62460A
16.REMOVE REAR ROOF SIDE RAIL GARNISH ASSEMBLY LH (for Full-trim)
62440D
17.REMOVE FRONT ROOF SIDE RAIL GARNISH ASSEMBLY LH (for Full-trim, w/ Rear Door)
63320E
18.REMOVE REAR ROOF HEADLINING ASSEMBLY (for Semi-trim for High Roof, w/ Rear Air Duct)
62740A
19.REMOVE REAR SIDE WINDOW ASSEMBLY LH
|
Protective Tape |
Apply protective tape to the outer surface of the vehicle body to prevent scratches.
- NOTICE:
-
When separating the rear side window assembly LH from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.
| *a | Matchmark |
When reusing the rear side window assembly LH:
Place matchmarks over the glass and vehicle body at the locations indicated in the illustration.
Install the suction cups to the rear side window assembly LH.
| *1 | Quarter Window Glass Spacer |
| *2 | Rear Side Window Clip LH |
| *a | Piano Wire |
From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.
Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
- NOTICE:
-
When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.
Cut through the adhesive by pulling the piano wire around the rear side window assembly LH.
Using suction cups, disconnect the quarter window glass spacer and rear side window clip LH and remove the rear side window assembly LH.
- NOTICE:
-
Do not drop the rear side window assembly LH.
20.REMOVE NO. 1 QUARTER PANEL SPACER
Remove the 2 No. 1 quarter panel spacers from the body.