RM3660EC _56 Audio / Visual / Telematics _080752 NAVIGATION / MULTI INFO DISPLAY _0391865 NAVIGATION SYSTEM(for Gasoline Model with RST Switch) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Gasoline Model with RST Switch)  Illumination Circuit  


DESCRIPTION

Power is supplied to the navigation receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E418928E12
5.854,4.01 7.083,4.365 1.229,0.354 10 false Navigation Receiver Assembly 2.906,2.635 4.667,2.948 1.76,0.313 10 false Spiral Cable Sub-assembly 1.25,0.458 2.333,0.74 1.083,0.281 10 false from TAIL Relay 3.833,0.656 4.479,0.938 0.646,0.281 10 false PANEL 0.354,3.469 2.458,3.781 2.104,0.313 10 false Steering Pad Switch Assembly 2.698,2.188 3.083,2.469 0.385,0.281 10 false z3 2.708,1.625 3.094,1.906 0.385,0.281 10 false z3 3.771,1.635 4.156,1.917 0.385,0.281 10 false I82 3.771,2.198 4.156,2.479 0.385,0.281 10 false I82 5.625,1.51 6.01,1.792 0.385,0.281 10 false 10 5.698,2.698 6.083,2.979 0.385,0.281 10 false 7 5.906,2.844 6.448,3.146 0.542,0.302 10 false GND1 5.927,1.635 6.313,1.917 0.385,0.281 10 false ILL+ 3.198,1.531 3.583,1.813 0.385,0.281 10 false IL+2 3.208,2.083 3.594,2.365 0.385,0.281 10 false ILL- 3.76,1.417 4.146,1.698 0.385,0.281 10 false 14 3.802,1.99 4.188,2.271 0.385,0.281 10 false 9 2.74,1.417 3.125,1.698 0.385,0.281 10 false 1 2.74,2.01 3.125,2.292 0.385,0.281 10 false 6 5.865,3.792 6.323,3.99 0.458,0.198 10 false I167

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the navigation receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except navigation receiver assembly. B
No illumination comes on (navigation receiver assembly, hazard switch, heater control switch, etc.). C




A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the I82 spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I82-14 (IL+2) - Body ground Light control switch in tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.

Disconnect the I167 navigation receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I167-10 (ILL+) - Body ground Light control switch in tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR