RM35X0E _59 Vehicle Exterior _078503 DOOR / HATCH _0381017 POWER SLIDE DOOR SYSTEM J

DOOR / HATCH  POWER SLIDE DOOR SYSTEM  Power Slide Door LH does not Operate When Using Inside / Outside Handle  


DESCRIPTION

The slide door motor unit LH (slide door ECU LH) receives signals from the inside handle or outside handle in the slide door lock remote control assembly LH and performs power slide door open or close operations.

WIRING DIAGRAM

E416517E01
5.333,3.75 6.917,4.146 1.583,0.396 10 false Slide Door Motor Unit LH (Slide Door ECU LH) 5.573,2.281 6.792,2.75 1.219,0.469 10 false DS1 5.583,0.917 6.802,1.385 1.219,0.469 10 false DS2 0.875,3.615 2.094,4.083 1.219,0.469 10 false U7 5.333,3.573 6.552,4.042 1.219,0.469 10 false T4 5.365,2.125 6.583,2.594 1.219,0.469 10 false 8 5.323,0.792 6.542,1.26 1.219,0.469 10 false 7 4.438,0.74 5.656,1.208 1.219,0.469 10 false 2 4.406,2.115 5.625,2.583 1.219,0.469 10 false 1 4.427,2.823 5.646,3.292 1.219,0.469 10 false 3 4,1.042 5.219,1.51 1.219,0.469 10 false DS2 3.99,2.406 5.208,2.875 1.219,0.469 10 false DS1 3.99,3.156 5.208,3.625 1.219,0.469 10 false GND 0.875,3.792 3.813,4.135 2.938,0.344 10 false Slide Door Lock Remote Control Assembly LH 1.688,2.458 4.417,2.823 2.729,0.365 10 false Close Switch 1.177,1.063 3.906,1.427 2.729,0.365 10 false Open Switch (for Inside Handle) 1.104,1.729 3.833,2.094 2.729,0.365 10 false Open Switch (for Outside Handle)

CAUTION / NOTICE / HINT

NOTICE:

If the replacement, removal and installation of the slide door motor unit (slide door ECU) or disconnection of the connectors of the slide door motor unit (slide door ECU) has been performed, initialize the power slide door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER SLIDE DOOR SYSTEM>INITIALIZATION


PROCEDURE

1.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Exterior>DOOR / HATCH>POWER SLIDE DOOR SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Rear Left Door > Data List
Tester Display Measurement Item Normal Condition Reference Value Diagnostic Note
Handle Switch1 Slide door lock remote control assembly LH (close switch) signal ON or OFF ON: Slide door inside handle or outside handle close operation performed (slide door lock remote control assembly LH [close switch] on)
OFF: Slide door inside handle or outside handle operation not performed or open operation performed (slide door lock remote control assembly LH [close switch] off) 		-
Handle Switch2 Slide door lock remote control assembly LH (open switch) signal ON or OFF ON: Slide door inside handle or outside handle open operation performed (slide door lock remote control assembly LH [open switch] on)
OFF: Slide door inside handle or outside handle operation not performed or close operation performed (slide door lock remote control assembly LH [open switch] off) 		-
Body Electrical > Rear Left Door > Data List
Tester Display
Handle Switch1
Handle Switch2
50003 160 6,7
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE SLIDE DOOR MOTOR UNIT LH (SLIDE DOOR ECU LH)

Click hereVehicle Exterior>DOOR / HATCH>POWER SLIDE DOOR MOTOR>REMOVAL


NG

2.INSPECT SLIDE DOOR LOCK REMOTE CONTROL ASSEMBLY LH
2.INSPECT SLIDE DOOR LOCK REMOTE CONTROL ASSEMBLY LH
a.

Remove the slide door lock remote control assembly LH.

except Wagon:

Click hereVehicle Interior>DOOR LOCK>SLIDE DOOR LOCK (except Wagon)>REMOVAL

for Wagon:

Click hereVehicle Interior>DOOR LOCK>SLIDE DOOR LOCK (for Wagon)>REMOVAL



b.

Inspect the slide door lock remote control assembly LH.

except Wagon:

Click hereVehicle Interior>DOOR LOCK>SLIDE DOOR LOCK (except Wagon)>INSPECTION

for Wagon:

Click hereVehicle Interior>DOOR LOCK>SLIDE DOOR LOCK (for Wagon)>INSPECTION



Result:
Result Proceed to
OK A
NG (except Wagon) B
NG (for Wagon) C



A

3.CHECK HARNESS AND CONNECTOR (SLIDE DOOR LOCK REMOTE CONTROL ASSEMBLY LH - SLIDE DOOR MOTOR UNIT LH [SLIDE DOOR ECU LH] AND BODY GROUND)

B

REPLACE SLIDE DOOR LOCK REMOTE CONTROL ASSEMBLY LH

Click hereVehicle Interior>DOOR LOCK>SLIDE DOOR LOCK (except Wagon)>REMOVAL


C

REPLACE SLIDE DOOR LOCK REMOTE CONTROL ASSEMBLY LH

Click hereVehicle Interior>DOOR LOCK>SLIDE DOOR LOCK (for Wagon)>REMOVAL


3.CHECK HARNESS AND CONNECTOR (SLIDE DOOR LOCK REMOTE CONTROL ASSEMBLY LH - SLIDE DOOR MOTOR UNIT LH [SLIDE DOOR ECU LH] AND BODY GROUND)
a.

Disconnect the U7 slide door lock remote control assembly LH connector.


b.

Disconnect the T4 slid door motor unit LH (slide door ECU LH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U7-2 (DS2) - T4-7 (DS2) Always Below 1 Ω
U7-1 (DS1) - T4-8 (DS1) Always Below 1 Ω
U7-3 (GND) - Body ground Always Below 1 Ω
U7-2 (DS2) or T4-7 (DS2) - Body ground Always 10 kΩ or higher
U7-1 (DS1) or T4-8 (DS1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SLIDE DOOR MOTOR UNIT LH (SLIDE DOOR ECU LH)

Click hereVehicle Exterior>DOOR / HATCH>POWER SLIDE DOOR MOTOR>REMOVAL


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR