RM35X0E _56 Audio / Visual / Telematics _078377 AUDIO / VIDEO _0385463 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Microphone signal is lost
·

Map light assembly

·

Telephone microphone assembly

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM


E419873
0.927,3.188 2.677,3.406 1.75,0.219 10 false a19*1, a22*3, a23*4 0.927,3.365 2.625,3.688 1.698,0.323 10 false Map Light Assembly 1.021,2.417 1.917,2.594 0.896,0.177 10 false A*1, B*2 1.021,2.583 2.438,3.177 1.417,0.594 10 false Telephone Microphone Assembly 1.552,1.115 2.01,1.313 0.458,0.198 10 false SNS2 2.104,1.979 2.563,2.177 0.458,0.198 10 false 2 2.115,0.979 2.573,1.177 0.458,0.198 10 false 1 1.625,2.135 2.083,2.333 0.458,0.198 10 false MIC- 2.594,1 3.052,1.198 0.458,0.198 10 false SNS2 3.125,0.635 3.583,0.833 0.458,0.198 10 false 11*1 2.604,1.99 3.063,2.188 0.458,0.198 10 false MCO- 3.125,1.677 3.583,1.875 0.458,0.198 10 false 10*1 5.625,2.917 6.875,3.469 1.25,0.552 10 false Radio and Display Receiver Assembly 5.625,2.698 6.083,2.896 0.458,0.198 10 false O7 5.771,1.146 6.229,1.344 0.458,0.198 10 false SNS2 5.802,2.146 6.26,2.344 0.458,0.198 10 false MIN- 5.479,0.99 5.938,1.188 0.458,0.198 10 false 25 5.49,1.99 5.948,2.188 0.458,0.198 10 false 22 0.385,3.99 2.01,4.208 1.625,0.219 10 false *1: except Wagon 3.146,0.823 3.604,1.021 0.458,0.198 10 false 3*3 3.135,1.021 3.594,1.219 0.458,0.198 10 false 12*4 3.125,1.854 3.583,2.052 0.458,0.198 10 false 4*3 3.125,2.031 3.583,2.229 0.458,0.198 10 false 11*4 1.927,4.01 5.198,4.229 3.271,0.219 10 false *3: for Wagon and w/ Telematics Transceiver 1.917,4.292 5.188,4.51 3.271,0.219 10 false *4: for Wagon and w/o Telematics Transceiver 0.406,4.281 2.031,4.5 1.625,0.219 10 false *2: for Wagon

CAUTION / NOTICE / HINT

NOTICE:

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

·

A communication malfunction DTC may be stored.

·

The radio and display receiver assembly may not operate normally.



HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PRECAUTION


PROCEDURE

1.CHECK MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
except Wagon A
for Wagon and w/ Telematics Transceiver B
for Wagon and w/o Telematics Transceiver C




A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

C

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the O7 radio and display receiver assembly connector.


b.

Disconnect the a19 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O7-25 (SNS2) - a19-11 (SNS2) Always Below 1 Ω
O7-22 (MIN-) - a19-10 (MCO-) Always Below 1 Ω
O7-25 (SNS2) - Body ground Always 10 kΩ or higher
O7-22 (MIN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E408533
1.51,0.271 1.885,0.521 0.375,0.25 1.177,1.198 1.063,0.333 1.063,0.333 0.885,0.333 true 1.031,1.177 0.865,0.615 0.865,0.615 0.688,0.615 true 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 0.458,0.25 0.969,0.458 0.51,0.208 10 false MCO- 0.281,0.531 0.813,0.792 0.531,0.26 10 false SNS2 1.594,0.313 1.906,0.51 0.313,0.198 10 false a19
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a19-11 (SNS2) - a19-10 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


NG

4.INSPECT MAP LIGHT ASSEMBLY
4.INSPECT MAP LIGHT ASSEMBLY
a.
E408103
1.573,0.396 1.958,0.646 0.385,0.25 1.5,2.813 1.896,3.063 0.396,0.25 0.979,1.417 0.656,0.833 0.656,0.833 0.51,0.833 true 1.146,1.406 1.458,0.823 1.458,0.823 1.615,0.823 true 1.469,3.479 1.219,3.896 1.219,3.896 1.073,3.896 true 1.656,3.49 1.948,3.906 1.948,3.906 2.104,3.906 true 0.198,0.354 0.51,0.552 0.313,0.198 10 false *a 1.656,0.729 2.156,0.948 0.5,0.219 10 false MCO- 0.104,0.74 0.583,0.948 0.479,0.208 10 false SNS2 1.656,2.854 1.969,3.052 0.313,0.198 10 false A 1.635,0.448 2.115,0.656 0.479,0.208 10 false a19 2.167,3.823 2.667,4.042 0.5,0.219 10 false MIC- 0.667,3.823 1.167,4.042 0.5,0.219 10 false SNS2 0.219,2.74 0.531,2.938 0.313,0.198 10 false *b
*a Component without harness connected
(Map Light Assembly [Wire Harness Side])
*b Component without harness connected
(Map Light Assembly [Telephone Microphone Assembly Side])


Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a19-11 (SNS2) - A-1 (SNS2) Always Below 1 Ω
a19-10 (MCO-) - A-2 (MIC-) Always Below 1 Ω
a19-11 (SNS2) - Body ground Always 10 kΩ or higher
a19-10 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL


NG

REPLACE MAP LIGHT ASSEMBLY

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the O7 radio and display receiver assembly connector.


b.

Disconnect the a22 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O7-25 (SNS2) - a22-3 (SNS2) Always Below 1 Ω
O7-22 (MIN-) - a22-4 (MCO-) Always Below 1 Ω
O7-25 (SNS2) - Body ground Always 10 kΩ or higher
O7-22 (MIN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for Wagon)>REMOVAL


b.
E419871C01
1.51,0.271 1.885,0.521 0.375,0.25 2.094,1.125 2.417,0.5 2.417,0.5 2.594,0.5 true 1.927,1.135 2.323,0.24 2.323,0.24 2.5,0.24 true 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 2.542,0.156 3.052,0.365 0.51,0.208 10 false MCO- 2.667,0.417 3.198,0.677 0.531,0.26 10 false SNS2 1.594,0.313 1.906,0.51 0.313,0.198 10 false a22
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a22-3 (SNS2) - a22-4 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


NG

7.INSPECT MAP LIGHT ASSEMBLY
7.INSPECT MAP LIGHT ASSEMBLY
a.
E419874
1.573,0.396 1.958,0.646 0.385,0.25 1.458,2.813 1.854,3.063 0.396,0.25 2.115,1.375 2.458,0.75 2.458,0.75 2.615,0.75 true 1.354,3.51 1.104,3.927 1.104,3.927 0.958,3.927 true 1.49,3.521 1.781,3.938 1.781,3.938 1.938,3.938 true 1.948,1.375 2.375,0.563 2.375,0.563 2.531,0.563 true 0.198,0.354 0.51,0.552 0.313,0.198 10 false *a 2.635,0.427 3.135,0.646 0.5,0.219 10 false MCO- 2.698,0.698 3.177,0.906 0.479,0.208 10 false SNS2 1.615,2.854 1.927,3.052 0.313,0.198 10 false B 1.635,0.448 2.115,0.656 0.479,0.208 10 false a22 1.979,3.844 2.479,4.063 0.5,0.219 10 false MIC- 0.531,3.854 1.031,4.073 0.5,0.219 10 false SNS2 0.219,2.74 0.531,2.938 0.313,0.198 10 false *b
*a Component without harness connected
(Map Light Assembly [Wire Harness Side])
*b Component without harness connected
(Map Light Assembly [Telephone Microphone Assembly Side])


Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for Wagon)>REMOVAL


b.

Disconnect the telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a22-3 (SNS2) - B-1 (SNS2) Always Below 1 Ω
a22-4 (MCO-) - B-2 (MIC-) Always Below 1 Ω
a22-3 (SNS2) - Body ground Always 10 kΩ or higher
a22-4 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL


NG

REPLACE MAP LIGHT ASSEMBLY

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the O7 radio and display receiver assembly connector.


b.

Disconnect the a23 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O7-25 (SNS2) - a23-12 (SNS2) Always Below 1 Ω
O7-22 (MIN-) - a23-11 (MCO-) Always Below 1 Ω
O7-25 (SNS2) - Body ground Always 10 kΩ or higher
O7-22 (MIN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for Wagon)>REMOVAL


b.
E419872C01
1.51,0.271 1.885,0.521 0.375,0.25 1.469,1.396 1.177,1.948 1.177,1.948 0.99,1.948 true 1.604,1.375 1.875,1.948 1.875,1.948 2.052,1.948 true 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 2.104,1.844 2.615,2.052 0.51,0.208 10 false MCO- 0.594,1.875 1.125,2.135 0.531,0.26 10 false SNS2 1.594,0.313 1.906,0.51 0.313,0.198 10 false a23
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a23-12 (SNS2) - a23-11 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


NG

10.INSPECT MAP LIGHT ASSEMBLY
10.INSPECT MAP LIGHT ASSEMBLY
a.
E419875C01
1.573,0.396 1.958,0.646 0.385,0.25 1.458,2.813 1.854,3.063 0.396,0.25 1.5,1.646 1.281,2.198 1.281,2.198 1.135,2.198 true 1.594,1.635 1.938,2.208 1.938,2.208 2.094,2.208 true 1.354,3.479 1.104,3.896 1.104,3.896 0.958,3.896 true 1.49,3.49 1.781,3.906 1.781,3.906 1.938,3.906 true 0.198,0.354 0.51,0.552 0.313,0.198 10 false *a 2.146,2.115 2.646,2.333 0.5,0.219 10 false MCO- 0.729,2.104 1.208,2.313 0.479,0.208 10 false SNS2 1.615,2.854 1.927,3.052 0.313,0.198 10 false B 1.635,0.448 2.115,0.656 0.479,0.208 10 false a23 1.979,3.823 2.479,4.042 0.5,0.219 10 false MIC- 0.531,3.823 1.031,4.042 0.5,0.219 10 false SNS2 0.219,2.74 0.531,2.938 0.313,0.198 10 false *b
*a Component without harness connected
(Map Light Assembly [Wire Harness Side])
*b Component without harness connected
(Map Light Assembly [Telephone Microphone Assembly Side])


Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for Wagon)>REMOVAL


b.

Disconnect the telephone microphone assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a23-12 (SNS2) - B-1 (SNS2) Always Below 1 Ω
a23-11 (MCO-) - B-2 (MIC-) Always Below 1 Ω
a23-12 (SNS2) - Body ground Always 10 kΩ or higher
a23-11 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE MICROPHONE ASSEMBLY>REMOVAL


NG

REPLACE MAP LIGHT ASSEMBLY

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL