RM36D0EC _59 Vehicle Exterior _083099 MIRROR (EXT) _0400988 POWER MIRROR CONTROL SYSTEM J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM  Mirror Heater does not Operate with Rear Defogger Switch  


DESCRIPTION

The air conditioning amplifier assembly detects the condition of the window defogger switch (mirror heater switch) in the air conditioning control assembly via LIN communication.

When the window defogger switch (mirror heater switch) is on, the air conditioning amplifier assembly sends the mirror heater drive command signal to the main body ECU (multiplex network body ECU) via CAN communication.

The main body ECU (multiplex network body ECU) sends the received mirror heater drive command signal to the power distribution box assembly via CXPI communication.

When the mirror heater drive command signal is received, the power distribution box assembly operates the mirror heater.

WIRING DIAGRAM

for SFTM Made:


E511530E04
4.427,0.719 4.74,0.917 0.313,0.198 10 false IC 5.688,0.708 6.302,0.906 0.615,0.198 10 false CXP1 5.302,0.708 5.458,0.906 0.156,0.198 10 false A 5.281,0.469 5.594,0.667 0.313,0.198 10 false 22 2.99,1.115 3.99,1.323 1,0.208 10 false MIR HTR Relay 1.844,0.865 2.156,1.063 0.313,0.198 10 false 6B 1.896,0.635 2.052,0.833 0.156,0.198 10 false 2 2.063,4.344 3.104,4.552 1.042,0.208 10 false Outer Mirror LH 1.396,5.083 3.698,5.281 2.302,0.198 10 false Outer Rear View Mirror Assembly LH 2.052,2.573 3.094,2.781 1.042,0.208 10 false Outer Mirror RH 1.365,3.292 3.667,3.49 2.302,0.198 10 false Outer Rear View Mirror Assembly RH 3.271,6.479 4.813,6.854 1.542,0.375 10 false Air Conditioning Amplifier Assembly 5.375,6.667 7.01,7.042 1.635,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 0.26,6.5 2.927,6.885 2.667,0.385 10 false Air Conditioning Control Assembly (Window Defogger Switch [Mirror Heater Switch]) 0.563,8.083 2.188,8.292 1.625,0.208 10 false : LIN Communication Line 0.563,8.458 2.292,8.646 1.729,0.188 10 false : CAN Communication Line 0.563,7.729 2.385,7.927 1.823,0.198 10 false : CXPI Communication Line 2.656,1.615 4.75,1.833 2.094,0.219 10 false Power Distribution Box Assembly 1.552,2.188 1.708,2.385 0.156,0.198 10 false + 1.563,3.938 1.719,4.135 0.156,0.198 10 false + 3.479,2.177 3.635,2.375 0.156,0.198 10 false - 3.5,3.938 3.656,4.135 0.156,0.198 10 false - 1.385,3.104 2.625,3.333 1.24,0.229 10 false I13*1, I17*2 1.385,4.885 2.729,5.073 1.344,0.188 10 false J13*1, J17*2 1.156,1.958 1.75,2.177 0.594,0.219 11 false 9*1 1.167,3.74 1.677,3.948 0.51,0.208 10 false 9*1 3.719,1.99 4.406,2.156 0.688,0.167 10 false 10*1 3.729,3.729 4.344,3.927 0.615,0.198 10 false 10*1 1.156,2.167 1.479,2.406 0.323,0.24 10 false 8*2 3.74,2.188 4.094,2.385 0.354,0.198 10 false 9*2 1.177,3.927 1.5,4.167 0.323,0.24 10 false 8*2 3.74,3.938 4.094,4.135 0.354,0.198 10 false 9*2 2.563,8.094 5.771,8.333 3.208,0.24 10 false *1: w/ Blind Spot Monitor System 2.563,8.458 5.771,8.698 3.208,0.24 10 false *2: w/o Blind Spot Monitor System


for GTMC Made:


E511530E05
4.427,0.719 4.74,0.917 0.313,0.198 10 false IC 5.688,0.708 6.302,0.906 0.615,0.198 10 false CXP1 5.302,0.708 5.458,0.906 0.156,0.198 10 false A 5.281,0.469 5.594,0.667 0.313,0.198 10 false 22 2.99,1.115 3.99,1.323 1,0.208 10 false MIR HTR Relay 1.844,0.865 2.156,1.063 0.313,0.198 10 false 6B 1.896,0.635 2.052,0.833 0.156,0.198 10 false 2 2.063,4.344 3.104,4.552 1.042,0.208 10 false Outer Mirror LH 1.396,5.083 3.698,5.281 2.302,0.198 10 false Outer Rear View Mirror Assembly LH 2.052,2.573 3.094,2.781 1.042,0.208 10 false Outer Mirror RH 1.365,3.292 3.667,3.49 2.302,0.198 10 false Outer Rear View Mirror Assembly RH 3.271,6.479 4.813,6.854 1.542,0.375 10 false Air Conditioning Amplifier Assembly 5.375,6.667 7.01,7.042 1.635,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 0.26,6.5 2.927,6.885 2.667,0.385 10 false Air Conditioning Control Assembly (Window Defogger Switch [Mirror Heater Switch]) 0.563,8.083 2.188,8.292 1.625,0.208 10 false : LIN Communication Line 0.563,8.458 2.292,8.646 1.729,0.188 10 false : CAN Communication Line 0.563,7.729 2.385,7.927 1.823,0.198 10 false : CXPI Communication Line 2.656,1.615 4.75,1.833 2.094,0.219 10 false Power Distribution Box Assembly 1.552,2.188 1.708,2.385 0.156,0.198 10 false + 1.563,3.938 1.719,4.135 0.156,0.198 10 false + 3.479,2.177 3.635,2.375 0.156,0.198 10 false - 3.5,3.938 3.656,4.135 0.156,0.198 10 false - 1.385,3.104 2.625,3.333 1.24,0.229 10 false I13*1, I14*2 1.385,4.885 2.729,5.073 1.344,0.188 10 false J13*1, J14*2 1.156,1.958 1.75,2.177 0.594,0.219 10 false 9*1 1.167,3.74 1.677,3.948 0.51,0.208 10 false 9*1 3.719,1.99 4.406,2.156 0.688,0.167 10 false 10*1 3.729,3.729 4.344,3.927 0.615,0.198 10 false 10*1 1.156,2.167 1.479,2.406 0.323,0.24 10 false 2*2 3.74,2.188 4.094,2.385 0.354,0.198 10 false 8*2 1.177,3.927 1.5,4.167 0.323,0.24 10 false 2*2 3.74,3.938 4.094,4.135 0.354,0.198 10 false 8*2 2.563,8.094 5.771,8.333 3.208,0.24 10 false *1: w/ Panoramic View Monitor System 2.563,8.458 5.771,8.698 3.208,0.24 10 false *2: w/o Panoramic View Monitor System


CAUTION / NOTICE / HINT

NOTICE:
·

If the mirror heater is operated when the auxiliary battery voltage is low, due to the electrical load limit control that gives voltage supply priority to the power steering system, the mirror heater may not operate. In this case, check the vehicle control history of the power steering system and check that "Battery Voltage Drop: X208F" is not stored before proceeding with troubleshooting.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>VEHICLE CONTROL HISTORY

·

With the negative (-) auxiliary battery terminal connected, disconnect/do not connect the connector of the power distribution box assembly.

·

When replacing the power distribution box assembly, the system may not operate normally if the same part number is not used.

·

The power mirror control system uses the CAN communication system, LIN communication system and CXPI communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system after confirming that the communication system is functioning properly.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.READ VALUE USING GTS (MIRROR HEATER INPUT SIGNAL)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Distribution Box > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Mirror Heater Input Signal Mirror heater drive signal (Input) OFF/ON OFF: Ignition switch ON, window defogger switch (mirror heater switch) off
ON: Ignition switch ON, window defogger switch (mirror heater switch) on 		-
Body Electrical > Power Distribution Box > Data List
Tester Display
Mirror Heater Input Signal
50003 475 1285
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

2.CHECK VEHICLE CONDITION

NG

14.CHECK AIR CONDITIONING SYSTEM
2.CHECK VEHICLE CONDITION
a.

Check vehicle condition.


Result:
Result Proceed to
Both mirror heater does not operate A
LH side mirror heater does not operate B
RH side mirror heater does not operate C



A

3.CHECK VEHICLE TYPE

B

6.CHECK VEHICLE TYPE

C

10.CHECK VEHICLE TYPE
3.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for GTMC Made A
for SFTM Made B



A

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - POWER DISTRIBUTION BOX ASSEMBLY AND BODY GROUND)

B

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - POWER DISTRIBUTION BOX ASSEMBLY AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - POWER DISTRIBUTION BOX ASSEMBLY AND BODY GROUND)
a.

Disconnect the I13*1 or I14*2 outer rear view mirror assembly RH connector.

*1: w/ Panoramic View Monitor System

*2: w/o Panoramic View Monitor System



b.

Disconnect the 6B power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Panoramic View Monitor System
Tester Connection Condition Specified Condition
I13-9 (+) - 6B-2 Always Below 1 Ω
I13-9 (+) or 6B-2 - Body ground Always 10 kΩ or higher


w/o Panoramic View Monitor System
Tester Connection Condition Specified Condition
I14-2 (+) - 6B-2 Always Below 1 Ω
I14-2 (+) or 6B-2 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - POWER DISTRIBUTION BOX ASSEMBLY AND BODY GROUND)
a.

Disconnect the I13*1 or I17*2 outer rear view mirror assembly RH connector.

*1: w/ Blind Spot Monitor System

*2: w/o Blind Spot Monitor System



b.

Disconnect the 6B power distribution box assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Blind Spot Monitor System
Tester Connection Condition Specified Condition
I13-9 (+) - 6B-2 Always Below 1 Ω
I13-9 (+) or 6B-2 - Body ground Always 10 kΩ or higher


w/o Blind Spot Monitor System
Tester Connection Condition Specified Condition
I17-8 (+) - 6B-2 Always Below 1 Ω
I17-8 (+) or 6B-2 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for GTMC Made A
for SFTM Made B



A

7.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - POWER DISTRIBUTION BOX ASSEMBLY)

B

9.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - POWER DISTRIBUTION BOX ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - POWER DISTRIBUTION BOX ASSEMBLY)
a.

w/ Panoramic View Monitor System:

i.

Disconnect the J13 outer rear view mirror assembly LH connector.


ii.

Disconnect the 6B power distribution box assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J13-9 (+) - 6B-2 Always Below 1 Ω
J13-10 (-) - Body Ground Always Below 1 Ω




b.

w/o Panoramic View Monitor System:

i.

Disconnect the J14 outer rear view mirror assembly LH connector.


ii.

Disconnect the 6B power distribution box assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J14-2 (+) - 6B-2 Always Below 1 Ω
J14-8 (-) - Body Ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

8.INSPECT OUTER MIRROR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - POWER DISTRIBUTION BOX ASSEMBLY)
a.

w/ Binde Spot Monitor System:

i.

Disconnect the J13 outer rear view mirror assembly LH connector.


ii.

Disconnect the 6B power distribution box assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J13-9 (+) - 6B-2 Always Below 1 Ω
J13-10 (-) - Body Ground Always Below 1 Ω




b.

w/o Blind Spot Monitor System:

i.

Disconnect the J17 outer rear view mirror assembly LH connector.


ii.

Disconnect the 6B power distribution box assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J17-8 (+) - 6B-2 Always Below 1 Ω
J17-9 (-) - Body Ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

8.INSPECT OUTER MIRROR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
for GTMC Made A
for SFTM Made B



A

11.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - POWER DISTRIBUTION BOX ASSEMBLY)

B

13.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - POWER DISTRIBUTION BOX ASSEMBLY)
11.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - POWER DISTRIBUTION BOX ASSEMBLY)
a.

w/ Panoramic View Monitor System:

i.

Disconnect the I13 outer rear view mirror assembly RH connector.


ii.

Disconnect the 6B power distribution box assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I13-9 (+) - 6B-2 Always Below 1 Ω
I13-10 (-) - Body Ground Always Below 1 Ω




b.

w/o Panoramic View Monitor System:

i.

Disconnect the I14 outer rear view mirror assembly RH connector.


ii.

Disconnect the 6B power distribution box assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I14-2 (+) - 6B-2 Always Below 1 Ω
I14-8 (-) - Body Ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

12.INSPECT OUTER MIRROR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - POWER DISTRIBUTION BOX ASSEMBLY)
a.

w/ Blind Spot Monitor System:

i.

Disconnect the I13 outer rear view mirror assembly RH connector.


ii.

Disconnect the 6B power distribution box assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I13-9 (+) - 6B-2 Always Below 1 Ω
I13-10 (-) - Body Ground Always Below 1 Ω




b.

w/o Blind Spot Monitor System:

i.

Disconnect the I17 outer rear view mirror assembly RH connector.


ii.

Disconnect the 6B power distribution box assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-8 (+) - 6B-2 Always Below 1 Ω
I17-9 (-) - Body Ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

12.INSPECT OUTER MIRROR RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK AIR CONDITIONING SYSTEM
a.

Check the air conditioning system.

for HV Model:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

for Gasoline Model:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

HINT:

Both the window defogger system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly via the same communication line.


OK:

The air conditioning system operates normally.



Result:
Proceed to
OK
NG



OK

15.CHECK AIR CONDITIONING CONTROL ASSEMBLY

NG

GO TO AIR CONDITIONING SYSTEM

for HV Model:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

for Gasoline Model:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING


15.CHECK AIR CONDITIONING CONTROL ASSEMBLY
a.

Check that the indicator illuminates when the window defogger switch (mirror heater switch) is on.

OK:

Defogger indicator illuminates.



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL


NG

REPLACE AIR CONDITIONING CONTROL ASSEMBLY

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL>REMOVAL