RM38T0EC _59 Vehicle Exterior _113746 DOOR / HATCH _0510849 KICK SENSOR A

DOOR / HATCH  KICK SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B609344N01
2.781,0.979 3.115,0.979 false 6.49,0.219 6.823,0.219 false 1.615,2.51 1.948,2.51 false 6.51,0.646 6.802,0.646 false 6.302,0.083 6.583,0.438 0.281,0.354 18 false 1 2.531,0.833 2.813,1.188 0.281,0.354 18 false 4 1.406,2.354 1.688,2.708 0.281,0.354 18 false 3 3.688,0.521 3.969,0.875 0.281,0.354 10 false x4 6.292,0.49 6.573,0.844 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 CABLE FROM NEGATIVE BATTERY TERMINAL 68960B - - -
3 REAR BUMPER ASSEMBLY 68946 (Click here) - -
4 KICK DOOR CONTROL SENSOR ASSEMBLY 891B0 - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front door removal/installation are shown below.

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*: for Gasoline Model

Front camera system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Stop and start system* Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


PROCEDURE

Hide 1. PRECAUTION

Z101186

CAUTION:
B401522

Be sure to read Precaution thoroughly before servicing.

Click here(Click here)


NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Z101186

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

If the airbag deploys for any reason, it may cause a serious accident.




Hide 3.REMOVE REAR BUMPER ASSEMBLY

Hide 891B0 4.REMOVE KICK DOOR CONTROL SENSOR ASSEMBLY

B587312