RM38N0EC _58 Vehicle Interior _111843 INTERIOR PANELS / TRIM _0501312 ROOF SUNSHADE(for Short Type Panoramic Fixed Moon Roof) A

INTERIOR PANELS / TRIM  ROOF SUNSHADE(for Short Type Panoramic Fixed Moon Roof)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during roof sunshade housing assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Reset back door close position Power Back Door System (Click here)
·

Roof sunshade ECU(Sliding roof drive gearassembly)*


·

Roof sunshade housingassembly*


Initialize panoramic fixedmoonroof with one-touchfrosted glass control system
·

Roof sunshade linkedfunction


·

Electric roof sunshadejam protection function


·

Single touch auto function


(Click here)

CAUTION:
B401522

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

for HV Model:

Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane Tracing Assist System Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision System

Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power Door Lock Control System
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air Conditioning System After the ignition switch is turned to ON, the servo motor standard position is recognized. -

·

for Gasoline Model:

Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane Tracing Assist System Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 seconds or more. (Click here)
Pre-collision System
Stop and Start System Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted (Click here)

Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power Door Lock Control System
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air Conditioning System After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 62170A 2.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 63231C 3.REMOVE ROOM LIGHT BRACKET

a.
B630017

Remove the 2 bolts.


b.

Disengage the 2 guides to remove the room light bracket.


Hide 4.REMOVE FRONT SLIDING ROOF HOUSING MOUNTING BRACKET LH

a.
B630015

Remove the 2 bolts and front sliding roof housing mounting bracket LH.


Hide 5.REMOVE FRONT SLIDING ROOF HOUSING MOUNTING BRACKET RH

HINT:

Use the same procedure described for the LH side.


Hide 6.REMOVE REAR SLIDING ROOF HOUSING MOUNTING BRACKET LH

a.
B630016

Remove the 2 bolts and rear sliding roof housing mounting bracket LH.


Hide 7.REMOVE REAR SLIDING ROOF HOUSING MOUNTING BRACKET RH

HINT:

Use the same procedure described for the LH side.


Hide 63250H 8.REMOVE SUNSHADE HOUSING ASSEMBLY

a.

Remove the 7 nuts and sunshade housing assembly.

B630018

NOTICE:

Do not damage the sunshade housing assembly or vehicle interior.