The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat airbag assembly removal/installation are shown below.
| Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
|
*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation. |
|||
·
Reclining motor (Front seatback frame sub-assembly LH)* ·
Slide motor (Front seat adjuster assembly LH)* ·
Front vertical motor (Front seat adjuster assembly LH)* ·
Lifter motor (Front seat adjuster assembly LH)* |
Initialize position control ECU | Front Power Seat Control System (w/ Memory) | ( 202111,999999,_58,_111839,_0505694,RM10000000206XI,)
|
| Disconnect cable from negative auxiliary battery terminal | Reset back door close position | Power Back Door System | ( 202111,999999,_59,_111831,_0505274,RM100000001ZMEG,)
|
| Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
|
*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation. |
|||
·
Reclining motor (Front seatback frame sub-assembly LH)* ·
Slide motor (Front seat adjuster assembly LH)* ·
Front vertical motor (Front seat adjuster assembly LH)* ·
Lifter motor (Front seat adjuster assembly LH)* |
Initialize position control ECU | Front Power Seat Control System (w/ Memory) | ( 202111,999999,_58,_111839,_0505694,RM10000000206XI,)
|
| Disconnect cable from negative auxiliary battery terminal | Reset back door close position | Power Back Door System | ( 202111,999999,_59,_111831,_0505274,RM100000001ZMEG,)
|
Be sure to read Precaution thoroughly before servicing.
Wear protective gloves. Sharp areas on the parts may injure your hands.
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
If a front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for SFTM Made Power Seat)>DISASSEMBLY202111,999999,_58,_111839,_0500775,RM100000001Z3EH,
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for SFTM Made Manual Seat)>DISASSEMBLY202111,999999,_58,_111839,_0501171,RM100000001Z57J,
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
| Effect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
| Lane Tracing Assist System | Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. | ( 202111,999999,_95,_111850,_0502173,RM100000001Z92I,)
|
| Pre-collision System |
| Effect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
| Power Door Lock Control System
·
Back door opener |
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. | ( 202111,999999,_58,_111830,_0505351,RM100000001ZMT3,)
|
| Air Conditioning System | After the ignition switch is turned to ON, the servo motor standard position is recognized. | - |
| Effect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
| Lane Tracing Assist System | Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 seconds or more. | ( 202111,999999,_95,_111850,_0502173,RM100000001Z92I,)
|
| Pre-collision System | ||
| Stop and Start System | Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted | ( 202406,999999,_51,_111803,_0509671,RM100000002KOGF,)
|
| Effect/Inoperative Function when Necessary Procedure not Performed | Necessary Procedure | Link |
|---|---|---|
| Power Door Lock Control System
·
Back door opener |
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. | ( 202111,999999,_58,_111830,_0505351,RM100000001ZMT3,)
|
| Air Conditioning System | After the ignition switch is turned to ON, the servo motor standard position is recognized. | - |
1.REMOVE FRONT SEAT ASSEMBLY (for Power Seat)
71074S
2.DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER (for Power Seat)
71868A
3.REMOVE FRONT SEAT INNER NO. 1 CUSHION SHIELD (for Power Seat)
71812D
4.REMOVE FRONT SEAT CUSHION SHIELD (for Power Seat)
71862
5.REMOVE FRONT SEAT INNER CUSHION SHIELD (for Power Seat)
6.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY (for Power Seat)
71876G
7.REMOVE LH SEAT RECLINING ADJUSTER INSIDE COVER (for Power Seat)
71931
8.REMOVE FRONT SEAT HEADREST SUPPORT (for Power Seat)
9.REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Power Seat)
10.REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)
71073S
11.DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER (for Manual Seat)
72525A
12.REMOVE RECLINING ADJUSTER RELEASE HANDLE (for Manual Seat)
71811D
13.REMOVE FRONT SEAT CUSHION SHIELD (for Manual Seat)
71861
14.REMOVE FRONT SEAT INNER CUSHION SHIELD (for Manual Seat)
15.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY (for Manual Seat)
71876F
16.REMOVE RECLINING ADJUSTER INSIDE COVER RH (for Manual Seat)
71931
17.REMOVE FRONT SEAT HEADREST SUPPORT (for Manual Seat)
18.REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Manual Seat)
73920A
19.REMOVE FRONT SEAT AIRBAG ASSEMBLY
|
Deployment Side |
When storing the front seat airbag assembly, keep the airbag deployment side facing upward.
Disengage the clamp.
Remove the 2 nuts and front seat airbag assembly.
Do not reuse the nuts.
Make sure that the front seatback frame sub-assembly is not deformed. If it is deformed, replace it with a new one.