RM38N0EC _52 Drivetrain _111806 K120 / K120F / K121 / K121F CVT _0525330 K120F / K121F FRONT DIFFERENTIAL OIL SEAL(for LH Side) A

K120 / K120F / K121 / K121F CVT K120F / K121F FRONT DIFFERENTIAL OIL SEAL(for LH Side) REPLACEMENT

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft oil seal LH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
1: Also necessary after performing a tire rotation. 2: It is not necessary to perform this procedure if the tire pressure warning valve and transmitters are installed to the same location.
Wheel alignment adjustment	· Perform reset memory · Perform "Calibration"	· DTCs are stored · ABS warning light illuminates · Slip indicator light illuminates · Electronically controlled brake system does not operate correctly	(202203,999999,_54,_111814,_0500728,RM1000000022HI0,)
Tires	· Initialization12 · Tire Position Identification12	Tire Pressure Warning System	Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System) (202203,202303,_V1,_111780,_0504977,RM1000000022CKZ,202303,202406,_V1,_111780,_0504977,RM100000002AA1Y,202406,202409,_V1,_111780,_0504977,RM100000002MO96,202409,999999,_V1,_111780,_0504977,RM100000002OMBP,)
Replacement of CVT fluid	ATF thermal degradation estimate reset	The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly	(202111,202303,_52,_111806,_0499726,RM100000001YZJA,202303,999999,_52,_111806,_0584611,RM1000000029R1M,)

PROCEDURE

Hide Display 1.REMOVE FRONT DRIVE SHAFT ASSEMBLY

Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY>REMOVAL202203,999999,_52,_111807,_0503131,RM100000002299J,

Hide Display 43420H 2.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

0.823,0.594 1.198,0.844 true 0.5,0.5 0.823,0.708 0.323,0.208 10 true SST

Using SST, remove the front drive shaft oil seal LH from the continuously variable transaxle assembly.

SST: 09308-00010

NOTICE:: Do not damage the continuously variable transaxle assembly.

Hide Display 43420H 3.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

1.698,1.188 1.104,0.677 1.104,0.677 1.625,0.927 true 2.417,2.417 2.583,2.417 2.583,2.417 2.635,2.667 false 2.135,2.583 2.302,2.583 2.302,2.583 2.479,2.729 false 0.75,0.563 1.083,0.771 0.333,0.208 10 true SST 2.198,2.323 2.51,2.479 0.313,0.156 10 false *a 1.938,2.479 2.25,2.635 0.313,0.156 10 false *b

*a	Inner Lip
*b	Outer Lip

Using SST and a hammer, install a new front drive shaft oil seal LH to the continuously variable transaxle assembly.

SST: 09950-70010 (09951-07150)
09649-17010

Standard Depth:: -0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

NOTICE:

2.292,1.073 2.427,1.073 2.427,1.073 2.427,1.406 false 1.323,1.26 1.552,1.26 false 2.219,0.75 2.583,0.75 false 0.729,0.75 1.094,0.75 false 1.052,0.281 1.333,0.51 0.281,0.229 10 false *a 2.542,0.281 2.823,0.51 0.281,0.229 10 false *b 2.125,0.979 2.406,1.208 0.281,0.229 10 false *c 1.594,1.156 1.875,1.385 0.281,0.229 10 false *c 0.427,0.677 0.885,0.875 0.458,0.198 10 false SST 1.917,0.677 2.375,0.875 0.458,0.198 10 false SST

*a	Correct
*b	Incorrect
*c	Outer Lip

Make sure that the outer lip of the front drive shaft oil seal LH is not pinched by SST.

Do not allow foreign matter to attach to the inner lip and outer lip of the front drive shaft oil seal LH.

Do not install the front drive shaft oil seal LH at an angle.

Do not remove the grease from the inner lip and outer lip of the front drive shaft oil seal LH.

Hide Display 4.INSTALL FRONT DRIVE SHAFT ASSEMBLY

Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY>INSTALLATION202203,999999,_52,_111807,_0503131,RM100000002299I,