RM36D0EC _59 Vehicle Exterior _083111 EXTERIOR PANELS / TRIM _0400773 BLACK OUT TAPE(for Front Door) A

EXTERIOR PANELS / TRIM BLACK OUT TAPE(for Front Door) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during black out tape are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure	Necessary Procedures	Effect/Inoperative Function when Necessary Procedures are not Performed	Link
· Front door glass sub-assembly LH · Front door glass sub-assembly RH · Front door glass run LH · Front door glass run RH	Initialize power window control system	· Auto up and down function · Jam protection function · Catch protection function · Remote control function · Wireless transmitter-linked function · Key-linked function · Key-off operation function · Window open warning function	(202409,999999,_59,_083107,_0400960,RM100000002NUSM,)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Lane tracing assist system	Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more.	(201910,999999,_58,_083101,_0401880,RM100000001JE9I,)
Pre-collision system		(201910,999999,_58,_083101,_0401880,RM100000001JE9I,)

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Power back door function	Fully close the back door by hand. HINT: Initialization is not necessary if the above procedures are performed while the back door is closed.	(202304,999999,_59,_083093,_0584672,RM1000000029PGT,)
Power door lock control system	If the back door is locked and therefore cannot be opened, it is necessary to unlock the back door using the door control switch, electrical key transmitter sub-assembly switch.	(202409,999999,_58,_083092,_0403003,RM100000002NS90,)
Air conditioning system	After the ignition switch is turned to ON, the servo motor standard position is recognized	-

Use the same procedure for the RH and LH sides.

The procedure listed below is for the LH side.

When performing removal for the front door belt moulding, disconnect the negative (-) auxiliary battery terminal after fully opening the front door glass.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure	Necessary Procedures	Effect/Inoperative Function when Necessary Procedures are not Performed	Link
· Front door glass sub-assembly LH · Front door glass sub-assembly RH · Front door glass run LH · Front door glass run RH	Initialize power window control system	· Auto up and down function · Jam protection function · Catch protection function · Remote control function · Wireless transmitter-linked function · Key-linked function · Key-off operation function · Window open warning function	(202409,999999,_59,_083107,_0400960,RM100000002NUSM,)

HINT:

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Stop and start system	Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes).	(202409,999999,_51,_083056,_0402418,RM100000002NSFO,)
Lane tracing assist system	Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more.	(201910,999999,_58,_083101,_0401880,RM100000001JE9I,)
Pre-collision system		(201910,999999,_58,_083101,_0401880,RM100000001JE9I,)

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
*: w/ Power back door system
Power back door function*	Fully close the back door by hand. HINT: Initialization is not necessary if the above procedures are performed while the back door is closed.	(202304,999999,_59,_083093,_0584672,RM1000000029PGT,)
Power door lock control system	If the back door is locked and therefore cannot be opened, it is necessary to unlock the back door using the door control switch, electrical key transmitter sub-assembly switch.	(202409,999999,_58,_083092,_0403003,RM100000002NS90,)
Air conditioning system	After the ignition switch is turned to ON, the servo motor standard position is recognized	-

Use the same procedure for the RH and LH sides.

The procedure listed below is for the LH side.

When performing removal for the front door belt moulding, disconnect the negative (-) auxiliary battery terminal after fully opening the front door glass.

PROCEDURE

Hide Display 1. PRECAUTION

NOTICE:: After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.; Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY202304,999999,_V1,_083041,_0402304,RM100000002AYZV,

Hide Display 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:: ·

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.

for M20D-FKS:

Click hereGeneral>MAINTENANCE>M20D-FKS BATTERY>REMOVAL202409,999999,_V1,_083136,_0403617,RM100000002NHPJ,

for A25B-FXS:

Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL202409,999999,_V1,_083136,_0403618,RM100000002NHPL,

for M20C-FKS:

Click hereGeneral>MAINTENANCE>M20C-FKS BATTERY>REMOVAL202409,999999,_V1,_083136,_0418197,RM100000002NHPI,

for A25D-FXS:

Click hereGeneral>MAINTENANCE>A25D-FXS AUXILIARY BATTERY>REMOVAL202409,999999,_V1,_083136,_0477834,RM100000002NHPM,

for A25F-FXS:

Click hereGeneral>MAINTENANCE>A25F-FXS AUXILIARY BATTERY (Production date from 2021/08)>REMOVAL202409,999999,_V1,_083136,_0486275,RM100000002NHPN,

Hide Display 69278B 3.REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY202409,999999,_59,_083093,_0403687,RM100000002NG1N_02_0006,

Hide Display 74640C 4.REMOVE DOOR ASSIST GRIP ASSEMBLY LH

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY202409,999999,_59,_083093,_0403687,RM100000002NG1N_02_0007,

Hide Display 5.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY202409,999999,_59,_083093,_0403687,RM100000002NG1N_02_0008,

Hide Display 6.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY202409,999999,_59,_083093,_0403687,RM100000002NG1N_02_0012,

Hide Display 67602 7.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY202409,999999,_59,_083093,_0403687,RM100000002NG1N_02_0001,

Hide Display 68172A 8.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY202409,999999,_59,_083093,_0403687,RM100000002NG1N_02_0026,

Hide Display 68193C 9.REMOVE FRONT DOOR FRONT BELT SEAL LH

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY202409,999999,_59,_083093,_0403687,RM100000002NG1N_02_0028,

Hide Display 67832 10.REMOVE FRONT DOOR SERVICE HOLE COVER LH

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY202409,999999,_59,_083093,_0403687,RM100000002NG1N_02_0032,

Hide Display 68102 11.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY202409,999999,_59,_083093,_0403687,RM100000002NG1N_02_0034,

Hide Display 67664C 12.REMOVE DOOR FRAME GARNISH LH

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY202409,999999,_59,_083093,_0403687,RM100000002NG1N_02_0035,

Hide Display 68151E 13.REMOVE FRONT DOOR GLASS RUN LH

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY202409,999999,_59,_083093,_0403687,RM100000002NG1N_02_0036,

Hide Display 67402F 14.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY LH

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY202409,999999,_59,_083093,_0403687,RM100000002NG1N_02_0041,

Hide Display 68126 15.REMOVE FRONT DOOR FIX WINDOW GLASS LH

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY202409,999999,_59,_083093,_0403687,RM100000002NG1N_02_0015,

Hide Display 75720 16.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY LH

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR BELT MOULDING>REMOVAL202409,999999,_59,_083111,_0400758,RM100000002NG2J_01_0218,

Hide Display 67862 17.REMOVE FRONT DOOR WEATHERSTRIP LH

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR WINDOW FRAME MOULDING>REMOVAL202409,999999,_59,_083111,_0400761,RM100000002NG2N_01_0214,

Hide Display 75969 18.REMOVE FRONT DOOR REAR INNER BLACK OUT TAPE LH

HINT:: When removing the front door rear inner black out tape LH, if it is difficult to remove, heat the adhesive of the front door rear inner black out tape LH and front door panel using a heat light.

Standard:

Item	Temperature
Front Door Panel	40 to 60°C (104 to 140°F)
Front Door Rear Inner Black Out Tape LH	40 to 60°C (104 to 140°F)

CAUTION:

2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b

*a	Heated Part
*b	Heat Light

Do not touch the heat light and heated parts.

Touching the heat light may result in burns.

Touching heated parts for a long time may result in burns.

NOTICE:: Do not heat front door panel and front door rear inner black out tape LH excessively.

Pull back on one of the ends of the front door rear inner black out tape LH to remove it.

HINT:: When pulling on the front door rear inner black out tape LH, pull it parallel to the front door panel.

Hide Display 75939 19.REMOVE FRONT DOOR UPPER INNER BLACK OUT TAPE LH

HINT:: When removing the front door upper inner black out tape LH, if it is difficult to remove, heat the adhesive of the front door upper inner black out tape LH and front door panel using a heat light.

Standard:

Item	Temperature
Front Door Panel	40 to 60°C (104 to 140°F)
Front Door Upper Inner Black Out Tape LH	40 to 60°C (104 to 140°F)

CAUTION:

2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b

*a	Heated Part
*b	Heat Light

Do not touch the heat light and heated parts.

Touching the heat light may result in burns.

Touching heated parts for a long time may result in burns.

NOTICE:: Do not heat front door panel and front door upper inner black out tape LH excessively.

Pull back on one of the ends of the front door upper inner black out tape LH to remove it.

HINT:: When pulling on the front door upper inner black out tape LH, pull it parallel to the front door panel.

Hide Display 75922M 20.REMOVE NO. 1 BLACK OUT TAPE LH

HINT:: When removing the No. 1 black out tape LH, if it is difficult to remove, heat the adhesive of the No. 1 black out tape LH and front door panel using a heat light.

Standard:

Item	Temperature
Front Door Panel	40 to 60°C (104 to 140°F)
No. 1 Black Out Tape LH	40 to 60°C (104 to 140°F)

CAUTION:

2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b

*a	Heated Part
*b	Heat Light

Do not touch the heat light and heated parts.

Touching the heat light may result in burns.

Touching heated parts for a long time may result in burns.

NOTICE:: Do not heat front door panel and No. 1 black out tape LH excessively.

Pull back on one of the ends of the No. 1 black out tape LH to remove it.

HINT:: When pulling on the No. 1 black out tape LH, pull it parallel to the front door panel.