RM36D0EC _58 Vehicle Interior _083104 HEATING / AIR CONDITIONING _0403065 BLOWER UNIT A

HEATING / AIR CONDITIONING BLOWER UNIT REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during blower assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replacement Part or Procedure	Necessary procedures	Effect/Inoperative Function when Necessary Procedure not Performed	Link
No. 1 blower damper servo sub-assembly	Servo motor initialization (Air conditioning system)	DTCs are stored	(202409,999999,_58,_083104,_0402829,RM100000002NSIZ,)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function when Necessary Procedures not Performed	Necessary Procedures	Link
Lane tracing assist system	Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more.	(201910,999999,_58,_083101,_0401880,RM100000001JE9I,)
Pre-collision system		(201910,999999,_58,_083101,_0401880,RM100000001JE9I,)

Learning completes when vehicle is operated normally

Effect/Inoperative Function when Necessary Procedures not Performed	Necessary Procedures	Link
Power back door function	Fully close the back door by hand. HINT: Initialization is not necessary if the above procedures are performed while the back door is closed.	(202304,999999,_59,_083093,_0584672,RM1000000029PGT,)
Power door lock control system	If the back door is locked and therefore cannot be opened, it is necessary to unlock the back door using the door control switch, electrical key transmitter sub-assembly switch.	(202409,999999,_58,_083092,_0403003,RM100000002NS90,)
Air conditioning system	After the ignition switch is turned to ON, the servo motor standard position is recognized	-

Before removing the blower assembly, set the air conditioning to recirculation mode.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replacement Part or Procedure	Necessary procedures	Effect/Inoperative Function when Necessary Procedure not Performed	Link
No. 1 blower damper servo sub-assembly	Servo motor initialization (Air conditioning system)	DTCs are stored	(202409,999999,_58,_083104,_0402828,RM100000002NSHC,)

HINT:

Learning completes when vehicle is driven

Effect/Inoperative Function when Necessary Procedures not Performed	Necessary Procedures	Link
Stop and start system	Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes).	(202409,999999,_51,_083056,_0402418,RM100000002NSFO,)
Lane tracing assist system	Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more.	(201910,999999,_58,_083101,_0401880,RM100000001JE9I,)
Pre-collision system		(201910,999999,_58,_083101,_0401880,RM100000001JE9I,)

Learning completes when vehicle is operated normally

Effect/Inoperative Function when Necessary Procedures not Performed	Necessary Procedures	Link
*: w/ Power back door system
Power back door function*	Fully close the back door by hand. HINT: Initialization is not necessary if the above procedures are performed while the back door is closed.	(202304,999999,_59,_083093,_0584672,RM1000000029PGT,)
Power door lock control system	If the back door is locked and therefore cannot be opened, it is necessary to unlock the back door using the door control switch, electrical key transmitter sub-assembly switch.	(202409,999999,_58,_083092,_0403003,RM100000002NS90,)
Air conditioning system	After the ignition switch is turned to ON, the servo motor standard position is recognized	-

Before removing the blower assembly, set the air conditioning to recirculation mode.

PROCEDURE

Hide Display 1. PRECAUTION

CAUTION:: Be sure to read Precaution thoroughly before servicing.; ·

for GTMC Made:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for GTMC Made)>PRECAUTION202405,999999,_58,_083100,_0694959,RM100000002LV12,

·

for SFTM Made:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for SFTM Made)>PRECAUTION202409,999999,_58,_083100,_0694957,RM100000002NSNT,

NOTICE:: After turning the ignition switch off, waiting time may be required before disconnecting the cable from the auxiliary negative (-) battery terminal.; Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY202304,999999,_V1,_083041,_0402304,RM100000002AYZV,

Hide Display 2.REMOVE AIR CONDITIONING UNIT ASSEMBLY

for A25B-FXS:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for A25B-FXS)>REMOVAL202409,999999,_58,_083104,_0403064,RM100000002NFZ9,

for A25D-FXS:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for A25D-FXS)>REMOVAL202409,999999,_58,_083104,_0476992,RM100000002NHZT,

for M20C-FKS:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for M20C-FKS)>REMOVAL202409,999999,_58,_083104,_0417475,RM100000002NFZE,

for M20D-FKS:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for M20D-FKS)>REMOVAL202409,999999,_58,_083104,_0403509,RM100000002NFZK,

for A25F-FXS:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for A25F-FXS [Production date from 2021/08])>REMOVAL202409,999999,_58,_083104,_0482694,RM100000002NFZG,

Hide Display 87201 3.REMOVE NO. 1 AIR DUCT SUB-ASSEMBLY (for SFTM Made)

2.01,1.208 2.344,1.208 true 2.333,1.104 2.5,1.292 0.167,0.188 10 true *a

*a	Hidden Claw

Remove the screw.

Detach the claw to remove the No. 1 air duct sub-assembly.

NOTICE:: ·

Be careful not to deform or damage the lower heater case of the air conditioner unit assembly when removing the No. 1 air duct sub-assembly.

·

If the fitting part of the No. 1 air duct sub-assembly has been cracked or deformed during removal, make sure to replace the air duct with a new one. Failure to do so may cause the No. 1 air duct sub-assembly to fall off or noise to occur.

Hide Display 87211A 4.REMOVE NO. 2 AIR DUCT (for GTMC Made)

HINT:: Use the same procedure described as for No. 1 air duct sub-assembly (for SFTM Made).

Hide Display 87130D 5.REMOVE BLOWER ASSEMBLY

1.01,3.156 1.188,3.354 0.177,0.198 10 true *a 1.979,2.396 2.156,2.594 0.177,0.198 10 true *a 2.26,1.365 2.438,1.563 0.177,0.198 10 true *a 2.667,0.26 2.844,0.458 0.177,0.198 10 true *b

*a	Clamp
*b	Guide

Disconnect the connector.

Detach the clamp and guide.

Remove the 2 screws.

Detach the claw and guide and remove the blower assembly.