RM3660EC _58 Vehicle Interior _080748 SEAT BELT _0391775 OCCUPANT DETECTION SENSOR A

SEAT BELT  OCCUPANT DETECTION SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during occupant detection sensor (separate type front seat cushion pad) removal/installation are shown below.

CAUTION:
B401522

Be sure to read Precaution thoroughly before servicing.

except NR Series Engine:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (except NR Series Engine)>PRECAUTION

for NR Series Engine:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for NR Series Engine)>PRECAUTION


NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

for HV Model:

Items for which learning is completed by driving the vehicle
Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Front Camera System Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more. (Click here)

·

for Gasoline Model:

Items for which learning is completed by driving the vehicle
Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and Start System Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted (Click here)
Pre-collision System Perform steering sensor zero point calibration (Click here)
Lane Tracing Assist System
Front Camera System Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more. (Click here)



PROCEDURE

Hide 1.REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)

Hide 71074S 3.DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER (for Manual Seat)

Hide 72551B 4.REMOVE RECLINING HINGE COVER (for Manual Seat)

Hide 72525A 5.REMOVE RECLINING ADJUSTER RELEASE HANDLE (for Manual Seat)

Hide 8.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY (for Manual Seat)

Hide 9.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD (for Manual Seat)

Hide 10.REMOVE OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD) (for Manual Seat)

a.

for Standard Seat Type:

i.

Using a screwdriver, disengage the 12 claws and remove the occupant detection sensor (separate type front seat cushion pad) from the separate type front seat cushion cover as shown in the illustration.(for Type A)

B685475C01
1.531,2.531 1.906,2.448 false 1.917,2.344 2.281,2.688 0.365,0.344 10 false *a
*a Screwdriver - -



ii.

Using a screwdriver, disengage the 12 claws and remove the occupant detection sensor (separate type front seat cushion pad) from the separate type front seat cushion cover as shown in the illustration.(for Type B)

B685476C01
1.51,2.594 1.958,2.375 false 1.99,2.271 2.292,2.542 0.302,0.271 10 false *a
*a Screwdriver - -




b.

for Sporty Seat Type:

i.

Using a screwdriver, disengage the 13 claws and remove the occupant detection sensor (separate type front seat cushion pad) from the separate type front seat cushion cover as shown in the illustration.(for Type A)

B685477C01
1.5,2.667 2,2.667 false 2.021,2.552 2.333,2.75 0.313,0.198 10 false *a
*a Screwdriver - -



ii.

Using a screwdriver, disengage the 12 claws and remove the occupant detection sensor (separate type front seat cushion pad) from the separate type front seat cushion cover as shown in the illustration.(for Type B)

B685478C01
1.49,2.667 1.99,2.667 true 2.021,2.563 2.333,2.76 0.313,0.198 10 false *a
*a Screwdriver - -




Hide 11.REMOVE FRONT SEAT ASSEMBLY (for Power Seat)

Hide 71073S 13.DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER (for Power Seat)

Hide 17.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY (for Power Seat)

Hide 18.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD (for Power Seat)

Hide 19.REMOVE OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD) (for Power Seat)

a.

for Standard Seat Type:

i.

Using a screwdriver, disengage the 12 claws and remove the occupant detection sensor (separate type front seat cushion pad) from the separate type front seat cushion cover as shown in the illustration.(for Type A)

B685475C02
1.5,2.667 2.021,2.667 false 2.052,2.573 2.365,2.729 0.313,0.156 10 false *a
*a Screwdriver - -



ii.

Using a screwdriver, disengage the 12 claws and remove the occupant detection sensor (separate type front seat cushion pad) from the separate type front seat cushion cover as shown in the illustration.(for Type B)

B685476C02
1.5,2.667 2.021,2.667 false 2.052,2.573 2.365,2.729 0.313,0.156 10 false *a
*a Screwdriver - -




b.

for Sporty Seat Type:

i.

Using a screwdriver, disengage the 12 claws and remove the occupant detection sensor (separate type front seat cushion pad) from the separate type front seat cushion cover as shown in the illustration.

B685478C02
1.5,2.667 2,2.667 false 2.021,2.552 2.333,2.75 0.313,0.198 10 false *a
*a Screwdriver - -