RM3660EC _56 Audio / Visual / Telematics _080752 NAVIGATION / MULTI INFO DISPLAY _0528911 NAVIGATION SYSTEM(w/o RST Switch (except 10.25 Inch Display)) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(w/o RST Switch (except 10.25 Inch Display))  Noise Occurs only for Radio  


CAUTION / NOTICE / HINT

HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (w/o RST Switch (except 10.25 Inch Display))>PRECAUTION


PROCEDURE

1.CHECK CONDITIONS AROUND THE TIME THE PROBLEM OCCURRED
a.

Check for situations/locations when noise occurs.


Result:
Result Proceed to
Noise occurs in all areas A
Noise occurs in specific areas B



A

2.CHECK FOR ADDITIONAL DEVICES (SUNSHADE FILM, TELECOMMICATIONS ANTENNAS, ETC)

B

RADIO WAVES ARE DISTURBED (RADIO WAVE ENVIRONMENT, ETC. EXTERNAL FACTOR)

2.CHECK FOR ADDITIONAL DEVICES (SUNSHADE FILM, TELECOMMICATIONS ANTENNAS, ETC)
a.

Check that there is no sunshade film or additional devices such as a telecommunications antenna installed.

OK:

AFTERMARKET DEVICES (INCLUDING NON-GENUINE WIRING) ARE NOT INSTALLED


HINT:

The vehicle is equipped with noise filters that prevent other systems in the vehicle from affecting the radio. Therefore, the system will not be affected by large interference. If the system is affected by large interference, confirm that no non-standard wire harnesses are installed, all of the noise filters are installed correctly, and the mount of the antenna is correctly earthed.



Result:
Proceed to
OK
NG



OK

3.CHECK NAVIGATION RECEIVER ASSEMBLY

NG

AFTERMARKET DEVICES ARE THE NOISE SOURCE

3.CHECK NAVIGATION RECEIVER ASSEMBLY
a.

Disconnect the connector (E) from the navigation receiver assembly. Then operate the navigation receiver assembly again to check for noise.


Result:
Result Proceed to
Noise does not occur A
Noise occurs B



A

4.CHECK INSTALLATION OF ANTENNA EARTH

B

REPLACE NAVIGATION RECEIVER ASSEMBLY

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL


4.CHECK INSTALLATION OF ANTENNA EARTH
a.

Make sure that the mount of the antenna cord sub-assembly is earthed securely to the vehicle body.


b.

Make sure that the mount of the No. 2 antenna cord sub-assembly is earthed securely to the vehicle body.

OK:

Installation is normal



Result:
Proceed to
OK
NG



OK

5.INSPECT BACK WINDOW GLASS (DISCONNECT CONNECTOR)

NG

PROPERLY INSTALL ANTENNA EARTH

5.INSPECT BACK WINDOW GLASS (DISCONNECT CONNECTOR)
a.

With the connector between the back window glass and the No. 4 antenna cord sub-assembly disconnected, operate the navigation receiver assembly again and check for noise.


Result:
Result Proceed to
Noise occurs A
Noise does not occur B



A

6.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY (DISCONNECT CONNECTOR)

B

REPLACE BACK WINDOW GLASS

Click hereVehicle Exterior>WINDOW / GLASS>BACK WINDOW GLASS>REMOVAL


6.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY (DISCONNECT CONNECTOR)
a.

With the connector between the No. 3 antenna cord sub-assembly and No. 1 amplifier antenna assembly disconnected, operate the navigation receiver assembly again and check for noise.


Result:
Result Proceed to
Noise occurs A
Noise does not occur B



A

7.INSPECT NO. 1 AMPLIFIER ANTENNA ASSEMBLY (DISCONNECT CONNECTOR)

B

REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL


7.INSPECT NO. 1 AMPLIFIER ANTENNA ASSEMBLY (DISCONNECT CONNECTOR)
a.

With the connector between the No. 1 amplifier antenna assembly and No. 2 antenna cord sub-assembly disconnected, operate the navigation receiver assembly again and check for noise.


Result:
Result Proceed to
Noise occurs A
Noise does not occur B



A

8.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY (DISCONNECT CONNECTOR)

B

REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL


8.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY (DISCONNECT CONNECTOR)
a.

With the connector between the No. 2 antenna cord sub-assembly and antenna cord sub-assembly disconnected, operate the navigation receiver assembly again and check for noise.


Result:
Result Proceed to
Noise occurs A
Noise does not occur B



A

REPLACE ANTENNA CORD SUB-ASSEMBLY

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL


B

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL