RM3660EC _57 Power Source / Network _080760 NR Series BATTERY / CHARGING _0394911 CHARGING SYSTEM C

NR Series BATTERY / CHARGING  CHARGING SYSTEM  P058A01  Battery Monitor Module General Electrical Failure  


DESCRIPTION

The battery state sensor assembly detects the voltage, current and temperature of the battery. The battery state sensor assembly calculates State of Charge (SOC) based on the voltage and current of the battery and sends it to the ECM. Based on the signals received, the ECM adjusts the charging voltage of the generator assembly.

The battery state sensor assembly calculates the battery temperature based on changes in resistance of a built-in thermistor and sends it to the ECM. The ECM reduces the amount of charging current based on this signal in order to protect the battery.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P058A01 Battery Monitor Module General Electrical Failure Any of the following conditions is met with the Ignition switch ON. (1 trip detection logic):
·

Current is 999.939 A or more, or -1000 A or less for 3.2 seconds or more.

·

The difference between the maximum and minimum current is 0.0305 A or less for 100 seconds or more.

·

A current detection circuit malfunction signal is received.

·

The battery temperature is 105°C (221°F) or more, or -40°C (-40°F) or less for 3.2 seconds or more.

·

A temperature detection circuit malfunction signal is received.

·

Voltage is 15.98 V or more, or 6.0 V or less for 3.2 seconds or more.

·

A voltage detection circuit malfunction signal is received.

·

A writing error occurs in the battery state sensor internal memory (battery identification data).


·

Battery state sensor assembly

·

Battery

·

Wire harness or connector


Charge warning is not displayed DTC stored SAE Code: P058A

WIRING DIAGRAM

A426248
0.771,3.281 4.438,3.479 3.667,0.198 10 false : LIN Communication Line 1.51,0.792 2.25,1.083 0.74,0.292 10 false BATT-S 2.99,0.646 3.604,0.844 0.615,0.198 10 false +B 4.073,0.656 4.688,0.854 0.615,0.198 10 false LIN 5.51,0.635 5.969,0.833 0.458,0.198 10 false LIN 5.844,3.021 6.76,3.219 0.917,0.198 10 false ECM 2.969,1.333 4.281,1.677 1.313,0.344 10 false Battery State Sensor Assembly 2.958,1.167 3.417,1.365 0.458,0.198 10 false C86 2.781,0.531 3.073,1 0.292,0.469 10 false 1 4.406,0.49 4.854,0.854 0.448,0.365 10 false 2 5.24,0.49 5.521,0.75 0.281,0.26 10 false 61 0.896,2.313 2.729,2.51 1.833,0.198 10 false Battery 5.833,2.865 6.75,3.063 0.917,0.198 10 false C78 0.75,1.365 1.688,1.729 0.938,0.365 10 false BATT-MAIN

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When P162B87 (Lost Communication with Battery Monitor Module Missing Message) is output at the same time, perform troubleshooting for P162B87 (Lost Communication with Battery Monitor Module Missing Message) first.

Click herePower Source / Network>NR Series (BATTERY / CHARGING)>CHARGING SYSTEM>P162B87



PROCEDURE

1.CHECK BATTERY STATE SENSOR ASSEMBLY INSTALLATION CONDITION
a.

Check installation condition of the battery state sensor assembly.

Click herePower Source / Network>NR Series (BATTERY / CHARGING)>BATTERY CURRENT SENSOR>INSTALLATION


Result:
Proceed to
OK
NG



OK

2.CHECK CHARGING SYSTEM

NG

INSTALL THE BATTERY STATE SENSOR ASSEMBLY CORRECTLY

Click herePower Source / Network>NR Series (BATTERY / CHARGING)>BATTERY CURRENT SENSOR>INSTALLATION


2.CHECK CHARGING SYSTEM
a.

Check the charging system.

Click herePower Source / Network>NR Series (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CHARGING SYSTEM

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Check that the battery state sensor assembly connector is securely connected.

OK:

The connector is securely connected.



b.
A417367C12
1.521,0.125 1.938,0.344 0.417,0.219 0.667,1.75 0.667,1.5 0.667,1.5 1.552,1.146 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 1.604,0.156 1.917,0.354 0.313,0.198 10 false C86 0.615,1.792 0.927,1.99 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Battery State Sensor Assembly)


Disconnect the C86 battery state sensor assembly connector.


c.

Check the connector case and terminals for deformation or corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C86-1 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BATTERY STATE SENSOR ASSEMBLY

Click herePower Source / Network>NR Series (BATTERY / CHARGING)>BATTERY CURRENT SENSOR>REMOVAL


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - BATTERY STATE SENSOR ASSEMBLY)