SEAT OCCUPANT DETECTION SENSOR(for Manual Captain Seat) REMOVAL
CAUTION / NOTICE / HINT
- CAUTION:
- ·
Wear protective gloves. Sharp areas on the parts may injure your hands.
·There is risk of injury.
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the occupant detection sensor removal/installation are shown below.
| Replacement Part or Procedure | Necessary Procedures | Effect/Inoperative Function When Necessary Procedures not Performed | Link |
|---|---|---|---|
| Disconnect cable from negative (-) battery terminal | Memorize steering angle neutral point | Parking assist monitor system | ( 201902,999999,_56,_079315,_0385736,RM100000001GNRA,)
|
| Panoramic view monitor system | (201906,999999,_56,_079315,_0396274,RM100000001IGR3,)
|
- HINT:
- ·
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.
-Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures not Performed Necessary Procedures Link Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). ( 201902,999999,_51,_078825,_0382334,RM100000001GBQ1,)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. ( 201902,999999,_58,_078886,_0382740,RM100000001G6XB,)
Pre-collision system
-Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures not Performed Necessary Procedures Link Power slide door system Fully close the slide door by hand.
- HINT:
-
Initialization is not necessary if the above procedures are performed while the slide door is closed.
( 201902,999999,_59,_078503,_0381017,RM100000001FWXM,)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -
·Use the same procedure for RHD and LHD vehicles.
·The procedure listed below is for LHD vehicles.
·Use the same procedure for the RH and LH sides.
·The procedure listed below is for the LH side.
·The procedure listed below is a representative example.
·Use the same procedure for first row and second row, unless otherwise specified.
PROCEDURE
1. PRECAUTION (for First Row)
- CAUTION:
-
-
Be sure to read Precaution thoroughly before servicing.
- ·
- NOTICE:
- ·
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
·If the pretensioner has been deployed, replace any damaged parts as necessary.
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for First Row)
Disconnet the cable from the negative (-) battery terminal.
- CAUTION:
-
- ·
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
·If the airbag deploys for any reason, it may cause a serious accident.
3.REMOVE REAR SEAT ASSEMBLY LH
71849L
4.REMOVE NO. 1 SEAT ADJUSTER COVER CAP LH
72216B
5.REMOVE NO. 1 SEAT TRACK HANDLE CONTROL LEVER LH
72526J
6.REMOVE NO. 1 SEAT RECLINING ADJUSTER RELEASE HANDLE LH
71324Q
7.REMOVE NO. 1 SEAT CUSHION LH (for First Row)
71834J
8.REMOVE NO. 1 SEAT OUTER NO. 1 RECLINING COVER LH
71849K
9.REMOVE SEAT SIDE TABLE ADJUSTER COVER CAP (for First Row, RH Side)
78060C
10.REMOVE NO. 1 SEAT SIDE TABLE ASSEMBLY (for First Row, RH Side)
71826A
11.REMOVE NO. 1 SEAT INNER CUSHION MOULDING RH
72848D
12.REMOVE NO. 1 SEAT NO. 1 ARMREST CAP LH
72890C
13.REMOVE LH SEAT NO. 1 SEAT ARMREST ASSEMBLY LH
72880C
14.REMOVE LH SEAT NO. 1 SEAT ARMREST ASSEMBLY RH
- HINT:
-
Use the same procedure described for the LH side.
73375
15.REMOVE REAR SEAT SHOULDER BELT COVER LH
73390
16.REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH (ANCHOR)
17.REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD
79076N
18.REMOVE NO. 1 SEAT OUTER LEG COVER SUB-ASSEMBLY LH (for First Row)
79076M
19.REMOVE NO. 1 SEAT INNER LEG COVER SUB-ASSEMBLY RH (for First Row)
79959F
20.REMOVE NO. 1 SEAT LEG COVER LH (for First Row)
79959J
21.REMOVE NO. 2 SEAT NO. 1 LEG COVER LH (for Second Row)
79077G
22.REMOVE NO. 2 SEAT OUTER LEG COVER SUB-ASSEMBLY LH (for Second Row)
79077G
23.REMOVE NO. 2 SEAT INNER LEG COVER SUB-ASSEMBLY RH (for Second Row, w/o Power Supply Unit)
79959K
24.REMOVE NO. 2 SEAT NO. 2 LEG COVER LH (for Second Row)
25.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD
Detach the hook.
| *A | for First Row | *B | for Second Row |
for First Row:
Remove the 4 clips.
for Second Row:
Remove the 2 clips.
|
Protective Tape |
Disconnect the connector of the occupant detection sensor.
Using a thin-bladed screwdriver, detach the claw and remove the connector of the occupant detection sensor.
- HINT:
-
Tape the thin-bladed screwdriver tip before use.
Remove the separate type rear seat cushion cover with pad.
79136C
26.REMOVE NO. 1 SEAT CUSHION PAD LH (OCCUPANT DETECTION SENSOR)
Remove the 6 hog rings.
Remove the 15 hog rings and No. 1 seat cushion pad LH (occupant detection sensor).