M20F-FXS, M20G-FXS ENGINE CONTROL SFI SYSTEM PARTICULATE FILTER REGENERATION PROCEDURE
PARTICULATE FILTER REGENERATE PROCEDURE
PM Regenerate Mode is a procedure in which accumulated PM (Particulate Matter) in the GPF (Gasoline Particulate Filter) is forcibly oxidized.
This procedure increases the temperature of the GPF and promotes oxidization by a lean condition.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off and P selected.
Enter the following menus: Powertrain / Engine / Utility / PM Regenerate Mode.
- Powertrain > Engine > Utility
-
Tester Display PM Regenerate Mode - 50005 372 4576
Turn the GTS off.
Disconnect the GTS.
- HINT:
- ·
The vehicle will remain in PM Regenerate Mode even if the GTS is disconnected from the DLC3.
·To end PM Regenerate Mode, turn the ignition switch off.
Turn the A/C switch on.
Drive the vehicle at a speed of 60 km/h (37 mph) or more until the GPF warning light turns off, or the exhaust filter related message is no longer displayed on the multi-information display.
- CAUTION:
-
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
- NOTICE:
-
For hybrid vehicles, the engine speed during forced particulate filter regeneration will be higher than normal.
- ·
Before driving, check that no DTCs other than those related to the GPF (Gasoline Particulate Filter) system are stored.
·When in PM Regenerate Mode, for hybrid vehicles, the engine speed during forced particulate filter regeneration will be higher than normal.
- HINT:
- ·
When the vehicle is driven in a manner in which particulate filter regeneration is performed, the GPF warning light will blink at a 2 second interval or a message indicating that PM regeneration is in progress will be displayed on the multi-information display.
-Particulate filter regeneration can be judged as being performed based on the GPF warning light state or the display of the particulate filter regeneration in progress message on the multi-information display.
-If the vehicle speed decreases due to traffic conditions, etc. and particulate filter regeneration stops, it will continue when the vehicle speed is increased.
·Continuously drive the vehicle at a speed of 60 km/h (37 mph) or more to perform particulate filter regeneration.
-The engine speed will be adjusted automatically, so drive in the D range.
-While the vehicle is in PM Regenerate Mode, the MIL or go to service warning light may illuminate and engine output may be restricted, but if particulate filter regeneration is being performed, it will continue.
-Driving on roads which allow high speed driving (90 to 100 km/h (56 to 62 mph)), such as a freeway, can reduce the time it takes to perform particulate filter regeneration.
-Engine braking may be not as effective during PM Regenerate Mode.
·When the accumulated PM has dropped below a certain amount, the GPF warning light will turn off, or the exhaust filter related message will no longer be displayed on the multi-information display.
- ·
If forced particulate filter regeneration is performed at the request of the customer (for example: "Exhaust Filter Full" is displayed on the multi-information display), it will continue until the PM Deposition Ratio is 30% or less.
If the GPF warning light does not turn off or the exhaust filter related message continues to be displayed on the multi-information display after the vehicle is driven at a speed of 60 km/h (37 mph) or more for 60 minutes or more to perform particulate filter regeneration, check the Vehicle Control History (RoB).
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).
- Powertrain > Engine > Utility
-
Tester Display Vehicle Control History (RoB) - 50005 372 55
| Code | Item | Vehicle Control History Freeze Frame Data Item "GPF Rejuvenate Impossibility History" | Corrective Action |
|---|---|---|---|
| X0856 | GPF Rejuvenate Interruption | Interruption by Heat Damage | Idle the engine for 5 minutes before performing particulate filter rejuvenation again. Then, while performing particulate filter rejuvenation, occasionally decrease the vehicle speed to below 60 km/h (37 mph) to allow the exhaust parts to cool before continuing particulate filter rejuvenation. |
| Interruption by Misfire | Perform troubleshooting for DTC P030000.
(  202307,999999,_51,_144956,_0604911,RM100000002BWQU,P030000)
|
||
| A/F Instability | Perform troubleshooting for DTC P017100.
( 202307,999999,_51,_144956,_0604911,RM100000002BWQL,P017100)
|
||
| X0857 | GPF Rejuvenate Run Insufficiency | Not Correct Conditions | Drive the vehicle in a manner that increases the temperature of the GPF. |
- HINT:
- ·
Forced particulate filter rejuvenation is typically only necessary for users who frequently drive only short trips, where the temperature of the GPF catalyst does not increase sufficiently to oxidize PM. If the value of the Data List item "PM Deposition Ratio Bank1" is more than 30%, advice the customer to occasionally drive longer than normal, in order to help reduce the accumulation of PM.
·If the vehicle cannot be driven a long distance or for a long time, replace the GPF.