RM36D0EC _56 Audio / Visual / Telematics _083082 PARK ASSIST / MONITORING _0586733 PANORAMIC VIEW MONITOR SYSTEM T

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  PROBLEM SYMPTOMS TABLE  


NOTICE:
·

The following inspection procedure of the panoramic view monitor system is described on the assumption that the audio and visual system is normal. If the audio and visual system has any malfunction, first proceed with troubleshooting of the audio and visual system.

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



HINT:

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.


General
Symptom Suspected Area Link
Screen does not switch when the panoramic view monitor switch (combination switch assembly) is pressed. Proceed to "ECU Power Source Circuit" Click here
Diagnostic mode - Signal connection check (CAMERA SW check) Click here
Parking assist ECU Click here
Does not switch to the panoramic view and rear view screen when the shift position is in R. Diagnostic mode - Signal connection check (CAN check) Click here
Diagnostic mode - Signal connection check (SHIFT check) Click here
Parking assist ECU Click here
Image is not displayed on the panoramic view and rear view screen or rear view screen when the shift position is in R. Proceed to "Image from Camera for Panoramic View Monitor is Abnormal" Click here
Display does not switch to the see through view screen or moving view screen when the panoramic view monitor switch (combination switch assembly) is pressed. Diagnostic mode - Signal connection check (CAN check) Click here
Diagnostic mode - Signal connection check (CAMERA SW check) Click here
Parking assist ECU Click here
Display does not switch to the panoramic view and wide front view screen, the panoramic view and rear view screen or the two-side view screen when the panoramic view monitor switch (combination switch assembly) is pressed. Diagnostic mode - Signal connection check (CAN check) Click here
Diagnostic mode - Signal connection check (CAMERA SW check) Click here
Parking assist ECU Click here
Image is not displayed on the panoramic view and wide front view screen, the panoramic view and rear view screen or the two-side view screen when the panoramic view monitor switch (combination switch assembly) is pressed. Proceed to "Image from Camera for Panoramic View Monitor is Abnormal" Click here

Display Malfunction
Symptom Suspected Area Link
Objects are not displayed correctly on the panoramic view monitor screen (color, distorted image). Proceed to "Image from Camera for Panoramic View Monitor is Abnormal" Click here
Distorted display on the panoramic view screen. Camera view adjustment (calibration) Click here
Parking assist ECU Click here
Parking lines do not match at front and rear on the panoramic view screen. Camera view adjustment (calibration) Click here
Parking assist ECU Click here
Partial black screen on the panoramic view screen. Camera view adjustment (calibration) Click here
Proceed to "Image from Camera for Panoramic View Monitor is Abnormal" Click here
Area displayed differs from the actual area. Ensure no door is opened -
Camera view adjustment (calibration) Click here
Parking assist ECU Click here

Switch Function
Symptom Suspected Area Link
Panoramic view monitor switch (combination switch assembly) night illumination does not illuminate. Panoramic view monitor switch (combination switch assembly) Click here
Harness or connector -
Touch switch operation is not accepted. Audio and visual system - Touch switch self check*1 Click here
Navigation system - Touch switch self check*2 Click here
Parking assist ECU Click here
Radio and display receiver assembly*1 Click here
Navigation receiver assembly*2 Click here
The touch function of the screen does not operate for the panoramic view monitor system. Parking assist ECU Click here
Radio and display receiver assembly*1 Click here
Navigation receiver assembly*2 Click here

Panoramic View Monitor System Function
Symptom Suspected Area Link
When the vehicle speed increases in the automatic display mode, the panoramic view and wide front view screen, the panoramic view and rear view screen or the two-side view screen remains displayed, without switching to the navigation screen. Parking assist ECU Click here
The screen display timer function does not operate if the manual display mode is selected. Parking assist ECU Click here
The estimated course lines do not match the vehicle width extension lines when the steering wheel points straight ahead. Check the steering wheel installation angle Click here
Camera view adjustment (calibration) Click here
Parking assist ECU Click here
"!" is displayed and the estimated course lines are not displayed. Check if the back door is not open -
Parking assist ECU Click here
Radio and display receiver assembly*1 Click here
The estimated course lines are not displayed. Check the panoramic view monitor screen display mode settings (Check if the estimated course lines display is set to off) -
Parking assist ECU Click here
"!" is displayed. Diagnostic mode - Signal connection check (CAN check) Click here
Electric parking brake system (for HV Model) Click here
Electric parking brake system (for Gasoline Model) Click here
"!" is displayed and all the buttons on the screen are grayed out. Camera view adjustment (calibration) Click here
Audio and visual system Click here
"!" is displayed and all the buttons on the screen are grayed out even after parking assist ECU initialization has been completed. Parking assist ECU Click here
Audio and visual system Click here
Guide lines and buttons are not displayed on the panoramic view and rear view screen display screen. Check if the back door is not open -
Check if the back door light turns on and off normally (If not, refer to Lighting System (Interior) - Problem Symptoms Table) Click here
Parking assist ECU Click here
"CHK" is displayed for an item on the Vehicle Signal Check screen. Diagnostic mode - Signal connection check Click here
Blind spots in image. Ensure no door is opened -
Camera view adjustment (calibration) Click here
Camera boundary lines are poorly connected. Camera view adjustment (calibration) Click here
The estimated course lines are displaced. Camera view adjustment (calibration) Click here
All buttons on the panoramic view monitor are continuously grayed out. Audio and visual system Click here