RM38N0EC _58 Vehicle Interior _111841 HEATING / AIR CONDITIONING _0499794 BLOWER UNIT A

HEATING / AIR CONDITIONING  BLOWER UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during blower assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

Auxiliary battery terminal is disconnected/reconnected Reset back door close position Power Back Door System (Click here)
Steering sensor* Update ECU security key (Only necessary after replacement) Vehicle Control History (RoB) are stored (Click here)
No. 1 blower damper servo sub-assembly Servo motor initialization (Air Conditioning System) DTCs are stored (Click here)

CAUTION:
B401522

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Items for which learning is completed by driving the vehicle (for HV Model)
Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane Tracing Assist System Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision System

Items for which learning is completed by driving the vehicle (for Gasoline Model)
Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane Tracing Assist System Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 seconds or more. (Click here)
Pre-collision System
Stop and Start System Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted (Click here)

Items for which learning is completed by operating the vehicle normally
Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power Door Lock Control System
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air Conditioning System After the ignition switch is turned to ON, the servo motor standard position is recognized. -


HINT:

Before removing the blower assembly, set the air conditioning to recirculation mode.


PROCEDURE

Hide 87211 2.REMOVE NO. 1 AIR DUCT

a.
E448489

Remove the screw.


b.
E448490C01
0.583,1.854 0.896,2.052 0.313,0.198 10 false *a 2,0.604 2.156,0.802 0.156,0.198 10 true A
*a View A
V100137

Front


Disengage the 3 claws to remove the No. 1 air duct.

NOTICE:
·

Be careful not to deform or damage the heater case of the air conditioner unit assembly when removing the No. 1 air duct.

·

If the fitting part of the No. 1 air duct has been cracked or deformed during removal, make sure to replace the air duct with a new one. Failure to do so may cause the No. 1 air duct to fall off or noise to occur.




Hide 87130D 3.REMOVE BLOWER ASSEMBLY

a.

Disconnect the connector.

E478190C01
1.26,3.281 1.458,3.479 0.198,0.198 10 true *b 6.156,3.406 6.354,3.604 0.198,0.198 10 true *a 6.25,0.823 6.448,1.021 0.198,0.198 10 true *b
*a Clamp *b Guide



b.

Disengage the clamp.


c.

Remove the 2 screws.


d.

Disengage the 2 claws and 2 guides to remove the blower assembly from the air conditioning radiator assembly.