RM38N0EC _52 Drivetrain _111808 AXLE AND DIFFERENTIAL _0525512 REAR DIFFERENTIAL CARRIER OIL SEAL A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during diaphragm oil seal removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Also necessary after performing a tire rotation.

*2: It is not necessary to perform this procedure if the tire pressure warning valve and transmitters are installed to the same location.

*3: The vehicle height changes because of suspension or tire replacement.

Tires
·

Initialization*1*2

·

Tire Position Identification*1*2


Tire Pressure Warning System Refer to Procedures Necessary When Replacing Parts (for Tire Pressure Warning System)
(Click here)
Rear wheel alignment adjustment
·

Perform reset memory

·

Perform "Calibration"


·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

Electronically controlled brake system does not operate correctly


(Click here)
Suspension parts*3 Parking assist ECU initialization Panoramic View Monitor System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
Gas leaks from exhaust system Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION / NOTICE / HINT

CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 7.REMOVE DIAPHRAGM OIL SEAL

a.
C155113C06
0.458,0.271 0.802,0.625 false 2.406,1.625 2.104,0.583 2.104,0.583 2.302,0.583 false 1.365,0.729 1.542,0.885 0.177,0.156 10 *a 0.083,0.521 0.271,0.677 0.188,0.156 10 *b 0.302,0.104 0.677,0.26 0.375,0.156 10 SST 2.344,0.521 2.656,0.719 0.313,0.198 10 *1
*1 Diaphragm Oil Seal
*a Turn
*b Hold


Using SST, remove the diaphragm oil seal from the rear differential carrier sub-assembly.

SST
09308-10010  


Hide 8.INSTALL DIAPHRAGM OIL SEAL

a.
C293307C02
0.396,0.688 0.615,0.688 false 2.104,1.781 1.896,1.781 1.896,1.781 1.896,1.531 false 3.208,1.365 3.385,1.531 0.177,0.167 10 false *a 0.094,0.604 0.458,0.771 0.365,0.167 10 false SST 2.177,1.688 2.49,1.885 0.313,0.198 10 false *1
*1 Diaphragm Oil Seal
*a Distance


Using SST and a hammer, tap a new diaphragm oil seal into the rear differential carrier sub-assembly until it reaches the standard value.

SST
09710-30021  (09710-03121)
09950-60011  (09951-00570)
09950-70010  (09951-07100)

Standard distance:

6.5 to 7.5 mm (0.256 to 0.295 in.) (from the edge of the differential carrier sub-assembly)


NOTICE:
·

Tap the oil seal uniformly so that the oil seal is straight.

·

Do not tap the oil seal in too far.