RM38N0EC _54 Brake _111814 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0503031 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  C14E914  Right Rear Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC C051212

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>C051212

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C14E914 Right Rear Wheel Speed Sensor Supply Voltage Circuit Short to Ground or Open An open or short in the speed sensor power supply circuit is detected for 0.12 seconds or more.
·

Rear speed sensor RH

·

Wire harness or connector

·

Skid control sensor wire RH (No. 1 parking brake wire assembly)

·

Skid control ECU (brake actuator assembly)


Brake/EPB A

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

b.

Disconnect the j2 rear speed sensor RH connector.


Procedure2

c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

d.

Turn the ignition switch to ON.


Procedure3

e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(j2)Location & Routing

Click Connector(j2)Body>Parking Brake Wire Assy>Rear Speed Sensor RH

j2-2 (RA+) - j2-1 (RA-) Ignition switch ON 11 to 14 V


HINT:

The rear speed sensor RH (for 2WD) and rear speed sensor rotor RH are incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor RH (for 2WD) and rear speed sensor rotor RH need to be replaced, replace the rear axle hub and bearing assembly RH.



Result:
Proceed to
OK
NG


Post-procedure1

f.

None



OK

REPLACE REAR SPEED SENSOR RH

for 2WD: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB (for 2WD)>REMOVAL

for AWD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR (for AWD)>REMOVAL


NG

2.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE CIRCUIT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

b.

Disconnect the jK1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


Procedure2

c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

d.

Turn the ignition switch to ON.


Procedure3

e.
C418960C07
1.51,0.167 1.927,0.417 0.417,0.25 1.219,1.865 1.573,1.563 true 2.229,1.906 1.875,1.563 true 0.167,0.167 0.5,0.417 0.333,0.25 10 false *a 1.625,0.208 2.042,0.458 0.417,0.25 10 false jK1 1.042,1.906 1.406,2.125 0.365,0.219 10 false RR- 2.292,1.927 2.656,2.146 0.365,0.219 10 false RR+
*a Front view of wire harness connector
(to Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(jK1)Location & Routing

Click Connector(jK1)Body>Parking Brake Wire Assy>Parking Brake Wire Assembly RH and Floor Wire

jK1-3 (RR+) - jK1-4 (RR-) Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

f.

None



OK

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

b.

Disconnect the A40 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the jK1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


Procedure2

d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(jK1,A40)Location & Routing

Click Connector(jK1)Body>Parking Brake Wire Assy>Parking Brake Wire Assembly RH and Floor Wire

Click Connector(A40)Engine Compartment>Engine Room Main Wire / Transmission Wire>Brake Actuator Assembly

jK1-3 (RR+) or A40-22 (RR+) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

f.

None



OK

REPLACE BRAKE ACTUATOR ASSEMBLY

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model)>REMOVAL


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR