RM38N0EC _56 Audio / Visual / Telematics _111824 TELEMATICS _0502894 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B15C111  GNSS Antenna Circuit Short to Ground  B15C113  GNSS Antenna Circuit Open  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C111 GNSS Antenna Circuit Short to Ground Current to the navigation antenna assembly is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Short circuit)
·

Telematics transceiver

·

Navigation antenna assembly

·

Antenna cord sub-assembly


B15C113 GNSS Antenna Circuit Open Current to the navigation antenna assembly is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Open circuit)
·

Telematics transceiver

·

Navigation antenna assembly

·

Antenna cord sub-assembly



WIRING DIAGRAM

E360069E65
0.125,1.219 2.25,1.469 2.125,0.25 10 false Navigation Antenna Assembly 0.125,1.042 0.448,1.25 0.323,0.208 10 false D 5.646,0.969 5.969,1.177 0.323,0.208 10 false B 5.646,1.167 7.135,1.479 1.49,0.313 10 false Telematics Transceiver 3.604,0.719 3.854,0.927 0.25,0.208 10 false * 0.854,2.281 3.063,2.573 2.208,0.292 10 false *: Antenna Cord Sub-assembly 1.156,0.438 1.406,0.646 0.25,0.208 10 false 3 5.927,0.427 6.177,0.635 0.25,0.208 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION

·

Before replacing the telematics transceiver, refer to Service Bulletin.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 10 seconds or more.


d.

Turn the GTS on.


e.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

f.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

USE SIMULATION METHOD TO CHECK

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


NG

2.INSPECT NAVIGATION ANTENNA ASSEMBLY
3.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.

Remove the antenna cord sub-assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL


b.
E334514C53
0.656,1.031 1.031,1.281 0.375,0.25 1.885,0.875 2,0.313 false 0.792,1.073 1.104,1.271 0.313,0.198 10 false D 2.031,0.146 2.344,0.344 0.313,0.198 10 false 3a 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Component without harness connected
(Antenna Cord Sub-assembly)


Disconnect the D antenna cord sub-assembly connector.


c.
E418544C01
1.542,0.177 1.958,0.427 0.417,0.25 0.99,1.479 1.531,1.417 false 1.708,0.24 1.865,0.438 0.156,0.198 10 false B 0.823,1.406 1.156,1.604 0.333,0.198 10 false 1a 0.167,0.146 0.365,0.323 0.198,0.177 10 false *a
*a Component without harness connected
(Antenna Cord Sub-assembly)


Disconnect the B antenna cord sub-assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D-3 - B-1 Always Below 1 Ω
D-3a - B-1a Always Below 1 Ω
D-3 or B-1 - Body ground Always 10 kΩ or higher
D-3a or B-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE TELEMATICS TRANSCEIVER

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel)>REMOVAL