RM36D0EC _56 Audio / Visual / Telematics _083082 PARK ASSIST / MONITORING _0711992 BLIND SPOT MONITOR SYSTEM Y

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the blind spot monitor system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:

If there are any scratches or impact marks on the rear bumper, perform the blind spot monitor beam axis confirmation. If any abnormalities are found, perform the blind spot monitor sensor installation condition inspection.


Result:
Proceed to
NEXT



NEXT

3.INSPECT AUXILIARY BATTERY VOLTAGE
3.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage with the ignition switch off.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

for GTMC Made HV Model:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for GTMC Made HV Model)>DIAGNOSIS SYSTEM

for SFTM Made Gasoline Model:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for GTMC Made Gasoline Model)>DIAGNOSIS SYSTEM

for SFTM Made HV Model:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for SFTM Made HV Model)>DIAGNOSIS SYSTEM

for SFTM Made Gasoline Model:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for SFTM Made Gasoline Model)>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B



A

5.CHECK FOR DTC AND FREEZE FRAME DATA*

B

GO TO CAN COMMUNICATION SYSTEM

for GTMC Made HV Model:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for GTMC Made HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

for GTMC Made Gasoline Model:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for GTMC Made Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

for SFTM Made HV Model:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for SFTM Made HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

for SFTM Made Gasoline Model:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for SFTM Made Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING


5.CHECK FOR DTC AND FREEZE FRAME DATA*
a.

Refer to DTC Check / Clear the DTCs the blind spot monitor system.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor "B" > Trouble Codes
50001 460
Body Electrical > Blind Spot Monitor "A" > Trouble Codes
50001 461

b.

Record or print DTCs and freeze frame data, if necessary.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>FREEZE FRAME DATA


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

6.CHECK VEHICLE CONTROL HISTORY*

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DIAGNOSTIC TROUBLE CODE CHART


6.CHECK VEHICLE CONTROL HISTORY*
a.

Check for Vehicle control history and note any codes that are output.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>VEHICLE CONTROL HISTORY

Body Electrical > Blind Spot Monitor "B" > Utility
Tester Display
Vehicle Control History (RoB)
50005 460 55
Body Electrical > Blind Spot Monitor "A" > Utility
Tester Display
Vehicle Control History (RoB)
50005 461 55

Result:
Proceed to
Vehicle control history is not output
Vehicle control history is output



Vehicle control history is not output

7.PROBLEM SYMPTOMS TABLE

Vehicle control history is output

GO TO VEHICLE CONTROL HISTORY

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>VEHICLE CONTROL HISTORY


7.PROBLEM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table. A
Fault is listed in Problem Symptoms Table. B


HINT:

If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING




A

8.PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM*

B

GO TO PROBLEM SYMPTOMS TABLE

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE


9.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

10.PERFORM BEAM AXIS CONFIRMATION*
10.PERFORM BEAM AXIS CONFIRMATION*
a.

Confirm the blind spot monitor beam axis display and perform the blind spot monitor beam axis adjustment.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SENSOR>ADJUSTMENT


b.

Perform the blind spot monitor sensor installation condition inspection.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SENSOR>ADJUSTMENT


c.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor "B" > Trouble Codes
50001 460
Body Electrical > Blind Spot Monitor "A" > Trouble Codes
50001 461

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

11.PERFORM CONFIRMATION TEST

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DIAGNOSTIC TROUBLE CODE CHART


11.PERFORM CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END