RM36D0EC _52 Drivetrain _138817 K121F CVT _0584979 FRONT DIFFERENTIAL OIL SEAL(for RH Side) A

K121F CVT  FRONT DIFFERENTIAL OIL SEAL(for RH Side)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during differential side oil seal and front drive shaft oil seal RH removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Air bleed oil pump with motor assembly Stop and start system (Click here)
Front wheel alignment adjustment
1.

Perform "Reset Memory".

2.

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

PROCEDURE

Hide 41110G 3.REMOVE DIFFERENTIAL SIDE OIL SEAL

a.
C405193C01
1.083,0.75 1.333,0.75 1.333,0.75 2.052,1.063 false 0.917,0.656 1.229,0.854 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the differential side oil seal from the transaxle housing.

NOTICE:

Be careful not to damage the front differential case or transaxle housing.



Hide 43410M 4.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C405194E01
0.948,1.479 1.365,1.479 false 0.646,1.417 1.104,1.615 0.458,0.198 10 false SST

Using SST, remove the front drive shaft oil seal RH from the continuously variable transaxle assembly.

SST
09308-00010  

NOTICE:

Do not damage the continuously variable transaxle assembly.



Hide 43410M 5.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.

Coat the lip of a new front differential case oil seal with MP grease.


b.
C405195C01
2.031,0.833 1.063,0.427 1.063,0.427 2.365,0.729 false 0.771,0.354 1.229,0.552 0.458,0.198 10 false SST 2.156,0.167 2.469,0.365 0.313,0.198 10 false *a
*a Depth


Using SST and a hammer, install a new front drive shaft oil seal RH to the continuously variable transaxle assembly.

SST
09950-60011  (09951-00410)
09950-70010  (09951-07200)

Standard Depth:

24.5 to 25.5 mm (0.965 to 1.00 in.)


NOTICE:
·

Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal RH.

·

Do not remove the grease from the lip of the front drive shaft oil seal RH.




Hide 41110G 6.INSTALL DIFFERENTIAL SIDE OIL SEAL

a.

Coat the lip of a new differential side oil seal with MP grease.


b.
C405196C01
1.135,2.635 1.667,2.823 1.667,2.823 1.521,2.281 false 2.333,1.625 2.646,1.823 0.313,0.198 10 false *a 1.729,2.75 2.188,2.948 0.458,0.198 10 false SST
*a Depth


Using SST and a hammer, install the differential side oil seal to the transaxle housing.

SST
09649-17010  
09950-70010  (09951-07200)

Standard Depth:

5.5 to 6.5 mm (0.217 to 0.256 in.)


NOTICE:
·

Make sure to install the differential side oil seal as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the differential side oil seal.

·

Do not install the differential side oil seal at an angle.

·

Do not remove the grease from the lip of the differential side oil seal.