RM36D0EC _58 Vehicle Interior _083100 SUPPLEMENTAL RESTRAINT SYSTEMS _0400497 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the curtain shield airbag assembly removal/installation are shown below.

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door function Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Power door lock control system If the back door is locked and therefore cannot be opened, it is necessary to unlock the back door using the door control switch, electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized -



·

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane tracing assist system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*: w/ Power back door system

Power back door function* Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Power door lock control system If the back door is locked and therefore cannot be opened, it is necessary to unlock the back door using the door control switch, electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized -


·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read Precaution thoroughly before servicing.

·

for GTMC Made:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for GTMC Made)>PRECAUTION

·

for SFTM Made:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for SFTM Made)>PRECAUTION



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the auxiliary negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



·

for M20C-FKS:

Click hereGeneral>MAINTENANCE>M20C-FKS BATTERY>REMOVAL

·

for M20D-FKS:

Click hereGeneral>MAINTENANCE>M20D-FKS BATTERY>REMOVAL

·

for A25B-FXS:

Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL

·

for A25D-FXS:

Click hereGeneral>MAINTENANCE>A25D-FXS AUXILIARY BATTERY>REMOVAL

·

for A25F-FXS:

Click hereGeneral>MAINTENANCE>A25F-FXS AUXILIARY BATTERY (Production date from 2021/08)>REMOVAL


Hide 62180A 4.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH

CAUTION:
B399183C01
0.667,0.5 0.823,0.698 0.156,0.198 10 false .
V100155

Deployment Side


·

When storing the curtain shield airbag assembly, keep the airbag deployment side facing upward.

·

If the airbag deploys for any reason, it may cause a serious accident.



a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




c.

Disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector:

·

for GTMC Made:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for GTMC Made)>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR

·

for SFTM Made:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for SFTM Made)>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR




d.

for LH Side:

i.
B555920C01
2.042,0.771 2.208,0.948 0.167,0.177 10 true *a 1.594,1.021 1.76,1.198 0.167,0.177 10 true *b
*a Guide
*b Wire Harness Clamp


Detach the wire harness clamp.



e.

Remove the curtain shield airbag assembly LH deployment portion in the following order.

CAUTION:

Do not reuse the clip (A) and roof side inner garnish clip.


1.

Using No. 2 needle-nose pliers, remove the 4 pins from the 3 clips (A) and roof side inner garnish clip.

2.

Using 2 thin bladed screwdrivers, detach the claw (A) and remove the 3 clips (A) and roof side inner garnish clip together with the curtain shield airbag assembly LH deployment portion.

3.

Detach the claw (B).


B555921C02
2.448,1.115 2.698,0.865 true 4.146,1.156 4.396,0.906 true 4.854,1.271 5.104,1.021 true 5.427,1.531 5.677,1.281 true 2.438,5.031 2.688,4.781 true 4.125,5.083 4.375,4.833 true 4.865,5.188 5.115,4.938 true 5.427,5.438 5.677,5.188 true 2.781,6.729 3.115,6.729 true 2.781,2.771 3.115,2.771 true 4.833,3.292 4.688,3.552 4.688,3.552 5.292,3.281 true 4.844,7.219 4.698,7.479 4.698,7.479 5.302,7.208 true 2.833,5.063 3.083,4.813 true 4.51,5.135 4.76,4.885 true 5.188,5.323 5.438,5.073 true 3.417,5.573 3.667,5.323 true 1.104,5.458 1.354,5.208 true 1.094,1.542 1.344,1.292 true 3.417,1.656 3.667,1.406 true 2.833,1.135 3.083,0.885 true 4.521,1.198 4.771,0.948 true 5.177,1.406 5.427,1.156 true 5.021,2.667 4.667,2.417 4.667,2.417 5.271,2.667 true 5.021,6.583 4.667,6.333 4.667,6.333 5.271,6.583 true 1.74,2.375 1.969,2.313 true 1.729,6.302 1.958,6.24 true 0.115,0.094 0.51,0.438 0.396,0.344 12 false *A 5.104,0.906 5.313,1.094 0.208,0.188 10 true *1 0.177,3.958 0.573,4.302 0.396,0.344 12 false *B 5.677,1.177 5.854,1.344 0.177,0.167 10 true *1 4.396,0.802 4.573,0.969 0.177,0.167 10 true *2 2.698,0.76 2.875,0.927 0.177,0.167 10 true *1 2.677,4.677 2.854,4.844 0.177,0.167 10 true *1 4.365,4.729 4.542,4.896 0.177,0.167 10 true *2 5.677,5.083 5.854,5.25 0.177,0.167 10 true *1 5.094,4.844 5.271,5.01 0.177,0.167 10 true *1 3.135,6.625 3.313,6.792 0.177,0.167 10 false *c 3.135,2.667 3.313,2.833 0.177,0.167 10 false *c 4.563,3.521 4.74,3.688 0.177,0.167 10 false *a 4.573,7.448 4.75,7.615 0.177,0.167 10 false *a 0.99,5.406 1.167,5.573 0.177,0.167 10 true *b 3.26,5.542 3.438,5.708 0.177,0.167 10 true *b 3.073,4.708 3.25,4.875 0.177,0.167 10 true *b 4.719,4.813 4.896,4.979 0.177,0.167 10 true *b 5.385,5.021 5.563,5.188 0.177,0.167 10 true *b 0.958,1.5 1.135,1.667 0.177,0.167 10 true *b 3.271,1.625 3.448,1.792 0.177,0.167 10 true *b 3.063,0.792 3.24,0.958 0.177,0.167 10 true *b 4.75,0.854 4.927,1.021 0.177,0.167 10 true *b 5.406,1.052 5.583,1.219 0.177,0.167 10 true *b 4.51,2.313 4.688,2.479 0.177,0.167 10 false *d 4.51,6.219 4.688,6.385 0.177,0.167 10 false *d 1.979,2.208 2.156,2.375 0.177,0.167 10 false *e 1.99,6.146 2.167,6.313 0.177,0.167 10 false *e
*A except Moon Roof *B for Moon Roof
*1 Clip (A) *2 Roof Side Inner Garnish Clip
*a Claw (A) *b Claw (B)
*c Pin *d Thin-bladed Screwdriver
*e No. 2 Needle-Nose Pliers - -



f.

Remove the curtain shield airbag assembly LH inflator in the following order.

CAUTION:

Do not reuse the Bolt, clip (B).


except Moon Roof:
1.

Remove the bolt and detach the hook to remove the curtain shield airbag assembly LH strap.

2.

Remove the bolt and rear side of the curtain shield airbag assembly LH deployment portion.

3.

Pull down the curtain shield airbag assembly LH deployment portion and remove the 2 bolts.

4.

Detach the hook to remove the curtain shield airbag assembly LH inflator.


for Moon Roof:
1.

Remove the bolt and detach the hook to remove the curtain shield airbag assembly LH strap.

2.

Remove the bolt and rear side of the curtain shield airbag assembly LH deployment portion.

3.

Remove the 4 bolts from the bracket.

4.

Using a clip remover, detach the clip (B) to remove the bracket.

HINT:

Tape the clip remover tip before use.


5.

Pull down the curtain shield airbag assembly LH deployment portion and remove the 2 bolts and detach the guide and curtain shield airbag assembly LH inflator.


B555922C01
3.917,4.365 4.167,4.115 true 2.385,4.583 2.719,4.583 true 0.135,0.104 0.542,0.385 0.406,0.281 12 false *A 0.219,3.781 0.625,4.063 0.406,0.281 12 false *B 1.125,0.802 1.302,0.969 0.177,0.167 10 true *c 1.063,4.979 1.24,5.146 0.177,0.167 10 true *c 6.323,1.01 6.5,1.177 0.177,0.167 10 true *d 6.333,5.135 6.51,5.302 0.177,0.167 10 true *d 1.906,3.948 2.083,4.115 0.177,0.167 10 true *a 1.135,2.219 1.313,2.385 0.177,0.167 10 true *b 1.208,6.552 1.385,6.719 0.177,0.167 10 true *b 4.167,4.01 4.344,4.177 0.177,0.167 10 true *1 2.208,4.5 2.385,4.667 0.177,0.167 10 true *1
*A except Moon Roof *B for Moon Roof
*1 Clip (B) - -
*a Bracket *b Curtain Shield Airbag Assembly LH Inflator
*c Rear Side Bolt *d Strap
V100155

Protective Tape - -



g.

When reusing the curtain shield airbag assembly LH:

i.

Remove the clips (A), clips (B), roof side inner garnish clip and curtain shield airbag clip spacer from the curtain shield airbag assembly LH.

CAUTION:

Do not reuse the curtain shield airbag clip spacer.