WINDOW / GLASS  BACK DOOR GLASS(except Wagon)  REMOVAL  

87950 1.REMOVE OUTER UNDER REAR VIEW MIRROR ASSEMBLY (w/ Outer Under Rear View Mirror)

81570 2.REMOVE CENTER STOP LIGHT ASSEMBLY

69298 3.REMOVE BACK DOOR INSIDE HANDLE COVER (w/ Handle, w/ Cover)

69291 4.REMOVE BACK DOOR INSIDE HANDLE ASSEMBLY (w/ Handle)

69783B 5.REMOVE BACK DOOR INSIDE HANDLE BEZEL (w/ Handle, w/o Illumination)

69783B 6.REMOVE BACK DOOR INSIDE HANDLE BEZEL (w/ Handle, w/ Illumination)

67961A 7.REMOVE BACK DOOR PULL STRAP

67751 8.REMOVE BACK DOOR TRIM BOARD

9.REMOVE REAR WIPER ARM AND BLADE ASSEMBLY (w/ Rear Wiper)

85110R 10.REMOVE REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)

85143R 11.REMOVE REAR WIPER MOTOR GROMMET (w/ Rear Wiper)

82186 12.REMOVE NO. 1 REAR WINDOW WIRE (w/ Rear Window Defogger)

a.

0,0 0,0 false

	Wire Harness Connector
	Bolt

Disconnect the wire harness connector.

b.

Remove the bolt.

c.

Detach the clamp and remove the No. 1 rear window wire.

68131 13.REMOVE BACK DOOR GLASS

a.

w/ Rear Window Defogger:

i.

Disconnect the connector.

b.

0,0 0,0 false

Protective Tape

Apply protective tape to the outer surface of the vehicle body to prevent scratches.

NOTICE:

When separating the back door glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

c.

1.74,0.479 2.083,0.375 2.083,0.375 1.719,0.76 true 2.135,0.25 2.448,0.448 0.313,0.198 10 false *a

*a

Matchmark

When reusing the back door glass:

i.

Place matchmarks over the glass and vehicle body at the locations indicated in the illustration.

ii.

Install the suction cups to the back door glass.

d.

0.969,1.5 0.813,1.792 true 0.583,0.792 0.865,0.917 true 2.771,0.771 2.5,0.906 true 0.51,1.427 0.865,1.313 true 2.833,1.427 2.49,1.281 true 0.896,0.844 1.083,1.052 0.188,0.208 10 true *1 2.323,0.833 2.5,1.031 0.177,0.198 10 true *2 0.667,1.823 0.979,2.021 0.313,0.198 10 true *a 0.906,1.198 1.094,1.406 0.188,0.208 10 true *3 2.302,1.198 2.49,1.406 0.188,0.208 10 true *4

*1	Back Window Glass Clip LH
*2	Back Window Glass Clip RH
*3	No. 2 Back Door Glass Spacer
*4	No. 1 Back Door Glass Spacer
*a	Piano Wire

From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.

e.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

NOTICE:

When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

f.

Cut through the adhesive by pulling the piano wire around the back door glass.

g.

Using suction cups, disconnect the No. 1 back door glass spacer and the No. 2 back window glass spacer and remove the back door glass.

NOTICE:

Do not drop the back door glass.