The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during lower No. 1 instrument panel airbag assembly removal/installation are shown below.
| Replaced Part or Performed Procedure | Necessary Procedures | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| Battery terminal is disconnected/reconnected | Memorize steering angle neutral point | Parking assist monitor system | ( 201902,999999,_56,_079315,_0385736,RM100000001GNRA,)
|
| Panoramic view monitor system | ( 201906,999999,_56,_079315,_0396274,RM100000001IGR3,)
|
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
| Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
|
*: w/ Stop and start system |
||
| Stop and start system* | Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). | ( 201902,999999,_51,_078825,_0382334,RM100000001GBQ1,)
|
| Lane control system | Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. | ( 201902,999999,_58,_078886,_0382740,RM100000001G6XB,)
|
| Pre-collision system | ||
Learning completes when vehicle is operated normally
| Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| Power slide door system | Fully close the slide door by hand.
|
( 201902,999999,_59,_078503,_0381017,RM100000001FWXM,)
|
| Air conditioning system | After the ignition switch is turned to ON, the servo motor standard position is recognized. | - |
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
67912A
3.REMOVE FRONT DOOR OUTSIDE SCUFF PLATE LH
67914B
4.REMOVE FRONT DOOR SCUFF PLATE LH
62112
5.REMOVE COWL SIDE TRIM BOARD LH
55631A
6.REMOVE NO. 1 INSTRUMENT PANEL UNDER TRAY STOPPER
55011A
7.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
55318C
8.REMOVE INSTRUMENT SIDE PANEL LH
55641
9.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER
53601
10.REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
77306
11.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
55432D
12.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
55044C
13.REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
55433B
14.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
73900
15.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
|
Deployment Side |
When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.
If the airbag deploys for any reason, it may cause a serious accident.
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Remove the 3 bolts.
|
Remove in this Direction |
Detach the claw to remove the lower No. 1 instrument panel airbag assembly.
Disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector: