The ECM continuously monitors its main and sub CPUs. This self-check ensures that the ECM is functioning properly. If outputs from these CPUs are different and deviate from the standard, the ECM will illuminate the MIL and store a DTCs.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P060604 | Control Module Processor System Internal Failure | ECM main CPU malfunction (1 trip detection logic) | ECM | Comes on | DTC stored | SAE Code: P0606 |
| P060629 | Control Module Processor Signal Invalid | ECM main CPU malfunction (1 trip detection logic) | ECM | Comes on | DTC stored | SAE Code: P0606 |
| P06062A | Control Module Processor Signal Stuck in Range | ECM main CPU malfunction (1 trip detection logic) | ECM | Comes on | DTC stored | SAE Code: P0606 |
| P060647 | Control Module Processor Watchdog/Safety MCU Failure | ECM main CPU malfunction (1 trip detection logic) | ECM | Comes on | DTC stored | SAE Code: P0606 |
| Required Sensors/Components | ECM |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the GTS off.
Turn the ignition switch off.
Disconnect the GTS.
Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
Connect the cable to the negative (-) battery terminal.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Wait 1 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P060604, P060629, P06062A or P060647.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
When disconnecting and reconnecting the battery.
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTC.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
Connect the cable to the negative (-) battery terminal.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Wait 1 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P060604, P060629, P06062A or P060647 is output | B |
A
B