RM38T0EC _59 Vehicle Exterior _114146 WIPER / WASHER _0510034 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Front Wiper Motor Circuit  


DESCRIPTION

The windshield wiper relay assembly controls the windshield wiper motor assembly through this circuit.

WIRING DIAGRAM

E447450E02
1.521,0.51 1.833,0.708 0.313,0.198 10 false A55 1.615,0.302 1.771,0.5 0.156,0.198 10 false 4 1.229,0.49 1.542,0.688 0.313,0.198 10 false +2 4.344,1.844 4.656,2.042 0.313,0.198 10 false +S 4.396,2.573 4.552,2.771 0.156,0.198 10 false E 4.125,2.563 4.49,2.792 0.365,0.229 10 false 4 4.104,0.375 4.344,0.823 0.24,0.448 10 false 3 4.115,1.844 4.365,2.25 0.25,0.406 10 false 1 1.521,1.26 1.833,1.458 0.313,0.198 10 false A55 1.083,1.969 1.448,2.208 0.365,0.24 10 false +SM 1.208,1.24 1.521,1.438 0.313,0.198 10 false +1 1.615,1.76 1.979,2 0.365,0.24 10 false 6 1.615,1.031 1.979,1.271 0.365,0.24 10 false 2 0.115,2.563 2.406,3.031 2.292,0.469 10 false Windshield Wiper Relay Assembly 4.344,0.385 4.656,0.583 0.313,0.198 10 false +2 4.344,1.115 4.656,1.313 0.313,0.198 10 false +1 4.281,3.302 6.563,3.604 2.281,0.302 10 false Windshield Wiper Motor Assembly 1.521,1.979 1.833,2.177 0.313,0.198 10 false A56 4.104,1.115 4.354,1.521 0.25,0.406 10 false 5 4.281,3.094 4.594,3.292 0.313,0.198 10 false A31

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Wiper Lo Operation Function to operate the windshield wiper motor assembly in LO OFF or ON -
Front Wiper Hi Operation Function to operate the windshield wiper motor assembly in HI OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Front Wiper Lo Operation
50004 449 72
Body Electrical > Main Body > Active Test
Tester Display
Front Wiper Hi Operation
50004 449 73
OK:

Windshield wiper motor assembly operates normally.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

Click hereVehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>PROBLEM SYMPTOMS TABLE


NG

2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY
2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSPECTION

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WINDSHIELD WIPER MOTOR ASSEMBLY)

NG

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL


3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WINDSHIELD WIPER MOTOR ASSEMBLY)
a.

Disconnect the A55 and A56 windshield wiper relay assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-2 (+1) - A31-5 (+1) Always Below 1 Ω
A55-4 (+2) - A31-3 (+2) Always Below 1 Ω
A56-6 (+SM) - A31-1 (+S) Always Below 1 Ω
A55-2 (+1) or A31-5 (+1) - Body ground Always 10 kΩ or higher
A55-4 (+2) or A31-3 (+2) - Body ground Always 10 kΩ or higher
A56-6 (+SM) or A31-1 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A31-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

Click hereVehicle Exterior>WIPER / WASHER>WIPER ECU>REMOVAL


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR