The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the instrument panel passenger airbag assembly removal/installation are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Learning completes when vehicle is driven
| Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| Lane tracing assist system | Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. | ( 201910,999999,_58,_083101,_0401880,RM100000001JE9I,)
|
| Pre-collision system |
Learning completes when vehicle is operated normally
| Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| Power back door function | Fully close the back door by hand.
|
( 202304,999999,_59,_083093,_0584672,RM1000000029PGT,)
|
| Power door lock control system | If the back door is locked and therefore cannot be opened, it is necessary to unlock the back door using the door control switch, electrical key transmitter sub-assembly switch. | ( 202409,999999,_58,_083092,_0403003,RM100000002NS90,)
|
| Air conditioning system | After the ignition switch is turned to ON, the servo motor standard position is recognized | - |
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Learning completes when vehicle is driven
| Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| Stop and start system | Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). | ( 202409,999999,_51,_083056,_0402418,RM100000002NSFO,)
|
| Lane tracing assist system | Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. | ( 201910,999999,_58,_083101,_0401880,RM100000001JE9I,)
|
| Pre-collision system |
Learning completes when vehicle is operated normally
| Effect/Inoperative Function When Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
|
*: w/ Power back door system |
||
| Power back door function* | Fully close the back door by hand.
|
( 202304,999999,_59,_083093,_0584672,RM1000000029PGT,)
|
| Power door lock control system | If the back door is locked and therefore cannot be opened, it is necessary to unlock the back door using the door control switch, electrical key transmitter sub-assembly switch. | ( 202409,999999,_58,_083092,_0403003,RM100000002NS90,)
|
| Air conditioning system | After the ignition switch is turned to ON, the servo motor standard position is recognized | - |
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the auxiliary negative (-) battery terminal.
2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
for M20C-FKS:
Click hereGeneral>MAINTENANCE>M20C-FKS BATTERY>REMOVAL202409,999999,_V1,_083136,_0418197,RM100000002NHPI,
for M20D-FKS:
Click hereGeneral>MAINTENANCE>M20D-FKS BATTERY>REMOVAL202409,999999,_V1,_083136,_0403617,RM100000002NHPJ,
3.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
55950G
4.REMOVE DEFROSTER NOZZLE ASSEMBLY
55086
5.REMOVE NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY
55972C
6.REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT
82143C
7.REMOVE NO. 3 INSTRUMENT PANEL WIRE
| *a | Guide |
| *b | Wire Harness Clamp |
Disconnect the airbag connector.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector:
Detach the guide and wire harness clamp and remove the No. 3 instrument panel wire.
73960A
8.REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY
|
Deployment Side |
When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.
If the airbag deploys for any reason, it may cause a serious accident.
Remove the 2 screws.
Insert moulding remover B into the side of the airbag door facing the front of the vehicle and detach the hook.
Move the instrument panel passenger airbag assembly toward you, detach the hook near the rear of the vehicle, and then remove the instrument panel passenger airbag assembly.