RM36D0EC _57 Power Source / Network _083091 NETWORKING _0694855 CAN COMMUNICATION SYSTEM(for GTMC Made HV Model) L

NETWORKING  CAN COMMUNICATION SYSTEM(for GTMC Made HV Model)  PRECAUTION  


CAN COMMUNICATION SYSTEM TROUBLESHOOTING


a.

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for GTMC Made HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING


b.

Precaution for steering system handling

i.

Be careful when replacing parts. Incorrect replacement could affect the performance of the steering system and result in hazardous driving.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>PRECAUTION



c.

Precaution for SRS airbag system handling

NOTICE:

This vehicle is equipped with a supplemental restraint system (SRS) which includes parts such as airbags for the driver and passenger. Failure to carry out service operations in the correct sequence could cause unexpected SRS deployment during servicing and may cause a serious accident. Before servicing (including removal/installation, inspection and replacement of parts), be sure to read precaution for SRS airbag system.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for GTMC Made)>PRECAUTION



d.

Precaution for when disconnecting a wire harness from a CAN junction connector

i.

When disconnecting a wire harness from a CAN junction connector, use tape or tags to identify each connector and make sure to reconnect each connector to its original location on the CAN junction connector.

HINT:
·

Reconnecting a connector to a location other than its original location on the CAN junction connector will not affect system performance. However, reconnecting connectors to their original locations makes future maintenance easier and avoids negative effects on wire harnesses, such as excessive tension.

·

For information on how to identify the ECUs or sensors connected to the CAN junction connector, refer to Terminals of ECU.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for GTMC Made HV Model)>TERMINALS OF ECU





e.

Bus line repair

i.

When repairing a CAN line or other communication line, make sure the untwisted portion of the wires is as short as possible, and wrap the line with tape while twisting the Hi/Lo wires together so that there is no separation between them.

NOTICE:

Untwisting and separation between wires may degrade equipment performance.



ii.
C275045C03
1.813,0.813 2.229,0.396 false 2.271,0.281 2.583,0.438 0.313,0.156 10 *a
*a Bypass Wire


Do not use bypass wiring between connectors.

NOTICE:
·

The ability of the twisted bus lines to resist interference will be lost if bypass wiring is used.

·

Do not use a twisted pair of wires for bypass wiring.





f.

Connector handling

i.
C274177C05
1.198,1.74 1.396,1.375 false 1.198,1.74 1.844,1.25 false 1.063,1.729 1.375,1.927 0.313,0.198 10 *a
*a Tester Probe


When checking resistance with a tester, insert the tester probes from the backside (harness side) of the connector.


ii.
C275046C03
1.25,0.333 1.667,0.917 false 1.25,0.333 1.51,1.313 false 1.115,0.177 1.427,0.333 0.313,0.156 10 *a
*a Service Wire


When it is not possible to insert the tester from the backside of the connector, using service wires, measure from the front side of the connector.



g.

Precaution for when replacing a gateway function equipped ECU (sub bus monitoring ECU)

i.

When replacing a gateway equipped function ECU (sub bus monitoring ECU) with one which was installed to another vehicle, perform initialization of the sub bus monitoring ECU in order to clear stored bus information.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for GTMC Made HV Model)>UTILITY

NOTICE:

If the stored bus information does not match the current sub bus configuration, DTCs may be stored and fail-safe functions may operate.


HINT:

It is not necessary to perform initialization of a gateway monitoring ECU (sub bus monitoring ECU) when using a sub bus monitoring ECU which was installed to another vehicle with the same sub bus configuration.




h.

Precautions for when a gateway function equipped ECU (sub bus monitor ECU) detects communication DTCs for ECUs not connected to the ECU

i.

Refer to precautions when replacing a gateway function equipped ECU (sub bus monitoring ECU) and initialize the connection information of the ECU.


ii.

Clear the DTCs and check that no DTCs are output.



i.

Difference between genuine radio and display receivers and optional radio and display receivers

i.

Some optional radio and display receivers are available as CAN compatible devices. Be aware that some optional radio and display receivers do not have the same diagnostic features or characteristics of genuine radio and display receivers.

NOTICE:
·

Optional radio and display receivers receive data from the CAN communication system. However, most optional radio and display receivers do not send signals to the CAN bus main line.

·

Most optional radio and display receivers will not be displayed on the "CAN Bus Check" screen of the GTS.

·

When checking for DTCs using the GTS, DTCs for optional radio and display receivers will not be displayed on the GTS.






PRECAUTION WHEN REPLACING PARTS


a.

When the central gateway ECU (network gateway ECU) is replaced, update the ECU security key.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY