RM36D0EC
_59
Vehicle Exterior
_083109
WIPER / WASHER
_0402385
WIPER AND WASHER SYSTEM
J
WIPER / WASHER WIPER AND WASHER SYSTEM Front Wiper Motor Circuit
DESCRIPTION
The windshield wiper relay assembly controls the windshield wiper motor assembly through this circuit.
WIRING DIAGRAM
0.792,2.677 1.917,3.104
1.125,0.427
10
false
Windshield Wiper Relay Assembly
1.99,0.75 2.448,0.948
0.458,0.198
10
false
A5
1.99,1.385 2.448,1.583
0.458,0.198
10
false
A6
1.99,2.021 2.448,2.219
0.458,0.198
10
false
A5
1.646,0.75 1.958,0.948
0.313,0.198
10
false
+2
1.5,1.396 1.885,1.583
0.385,0.188
10
false
+SM
1.635,2.031 1.948,2.229
0.313,0.198
10
false
+1
2.031,0.542 2.188,0.74
0.156,0.198
10
false
4
2.042,1.177 2.354,1.375
0.313,0.198
10
false
6
2.042,1.813 2.198,2.01
0.156,0.198
10
false
2
3.854,0.635 4.01,0.833
0.156,0.198
10
false
4
3.854,1.281 4.01,1.479
0.156,0.198
10
false
3
3.844,1.885 4,2.083
0.156,0.198
10
false
1
4.063,0.625 4.375,0.823
0.313,0.198
10
false
+2
4.052,1.271 4.438,1.458
0.385,0.188
10
false
+S
4.052,1.885 4.365,2.083
0.313,0.198
10
false
+1
6.156,1.281 6.313,1.479
0.156,0.198
10
false
E
6.385,1.281 6.542,1.479
0.156,0.198
10
false
5
4.125,2.719 4.583,2.917
0.458,0.198
10
false
A93
4.125,2.896 6.281,3.125
2.156,0.229
10
false
Windshield Wiper Motor Assembly
PROCEDURE
1.PERFORM ACTIVE TEST USING GTS (FRONT WIPER OPERATION)
a.
Perform the Active Test according to the display on the GTS.
- Body Electrical > Main Body > Active Test
-
Tester Display Measurement Item Control Range Diagnostic Note Front Wiper Lo Operation Function to operate the windshield wiper motor assembly in LO OFF or ON - Front Wiper Hi Operation Function to operate the windshield wiper motor assembly in HI OFF or ON -
- Body Electrical > Main Body > Active Test
-
Tester Display Front Wiper Lo Operation - 50004 449 72
- Body Electrical > Main Body > Active Test
-
Tester Display Front Wiper Hi Operation - 50004 449 73
- OK:
Windshield wiper motor assembly operates normally.
- Result:
Proceed to OK NG
OK
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
NG
2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY
2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY
- Result:
Proceed to OK NG
OK
3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WINDSHIELD WIPER MOTOR ASSEMBLY)
NG
REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WINDSHIELD WIPER MOTOR ASSEMBLY)
a.
Disconnect the A5 and A6 windshield wiper relay assembly connectors.
b.
Disconnect the A93 windshield wiper motor assembly connector.
c.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition A5-2 (+1) - A93-1 (+1) Always Below 1 Ω A5-4 (+2) - A93-4 (+2) Always Below 1 Ω A6-6 (+SM) - A93-3 (+S) Always Below 1 Ω A5-2 (+1) or A93-1 (+1) - Body ground Always 10 kΩ or higher A5-4 (+2) or A93-4 (+2) - Body ground Always 10 kΩ or higher A6-6 (+SM) or A93-3 (+S) - Body ground Always 10 kΩ or higher
- Result:
Proceed to OK NG
OK
4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)
a.
1.479,0.167 1.927,0.417
0.448,0.25
1.875,1.479 2.292,1.833
2.292,1.833 2.521,1.833
true
0.104,0.073 0.417,0.229
0.313,0.156
10
false
*a
1.583,0.208 2.042,0.406
0.458,0.198
10
false
A93
2.646,1.729 2.802,1.927
0.156,0.198
10
false
E
| *a | Front view of wire harness connector
(to Windshield Wiper Motor Assembly) |
Disconnect the windshield wiper motor assembly connector.
b.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition A93-5 (E) - Body ground Always Below 1 Ω
- Result:
Proceed to OK NG
OK
REPLACE WINDSHIELD WIPER RELAY ASSEMBLY
Click hereVehicle Exterior>WIPER / WASHER>WIPER ECU>REMOVAL201910,999999,_59,_083109,_0402383,RM100000001JI4Q,
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR