DOOR / HATCH  REAR DOOR  REASSEMBLY  

Install the hole plug.

HINT:

Use the same procedure described for the other side.

Attach the claw and install the rear door panel cushion.

Attach the claw and install the screw grommet.

HINT:

Use the same procedure described for the other side.

Install the rear door lock child protection cover LH.

0.031,0.031 0.281,0.25 0.25,0.219 12 true *A 0.031,2.25 0.281,2.469 0.25,0.219 12 true *B

*A	for Type A
*B	for Type B

Attach the clip and install the rear door No. 5 weatherstrip LH.

Attach the claw to install a new door window frame moulding clip.

Attach the clip and install the rear door weatherstrip LH.

Attach the clip and install the clip.

1.396,1.208 1.708,1.365 0.313,0.156 10 false *a 1.385,2.229 1.698,2.385 0.313,0.156 10 false *b

*a	Correct
*b	Incorrect

Check that the rear door weatherstrip LH is securely installed to the rail of the rear door upper window frame moulding LH as shown in the illustration.

NOTICE:

If the rear door weatherstrip LH is not securely installed, water may leak into the vehicle.

0,0 0,0 false

	Bolt (A)
	Bolt (B)

Install the rear door check assembly to the body panel with the bolt (B).

Torque:

30 N*m (306 kgf*cm, 22 ft.*lbf)

0.167,0.156 0.427,0.396 0.26,0.24 10 true *a 0.156,2.438 0.396,2.656 0.24,0.219 10 true *b

*a	Inside
*b	Outside

Attach the guide as shown in the illustration.

Attach the guide and install the rear door rear outside handle pad.

Attach the claw and guide to install the rear door front outside handle pad.

0,0 0,0 false

Install in this Direction

Attach the claw and install the rear door outside handle cover as shown in the illustration.

Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the "TORX" screw.

Torque:

4.0 N*m (41 kgf*cm, 35 in.*lbf)

0,0 0,0 false

Install in this Direction

Install the rear door outside handle assembly LH by pushing and sliding it in the direction indicated by the arrow shown in the illustration.

1.938,1.521 1.938,1.844 1.938,1.844 2.25,1.844 true 2.323,1.771 2.552,1.958 0.229,0.188 10 true *1

*1	Holder
	Install in this Direction

Attach the holder as shown in the illustration.

0,0 0,0 false

Install in this Direction

Pull in the rear door window regulator sub-assembly LH through the service hole as shown in the illustration.

0.865,3.156 1.021,3.354 0.156,0.198 10 true 1 0.906,1.458 1.063,1.656 0.156,0.198 10 true 1 1.573,1.417 1.729,1.615 0.156,0.198 10 true 2 2.135,0.802 2.292,1 0.156,0.198 10 true 3 1.885,2.135 2.042,2.333 0.156,0.198 10 true 5 2.635,1.865 2.792,2.063 0.156,0.198 10 true 4

	Nut
	Connector

Install the rear door window regulator sub-assembly LH with the 6 nuts in the order shown in the illustration.

Torque:

8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Do not damage the rear door panel with the rear door window regulator sub-assembly LH.

0,0 0,0 false

Install in this Direction

Insert the rear door glass sub-assembly LH to the rear door panel in the shown in the illustration.

Install the rear door glass sub-assembly LH with the 2 bolts.

Torque:

8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Be careful not to damage the rear door glass sub-assembly LH.

Install the hole plug.

Install the rear door quarter window weatherstrip LH to the rear door quarter window glass LH.

0,0 0,0 false

Install in this Direction

Install the rear door quarter window glass LH with rear door quarter window weatherstrip LH as shown in the illustration.

0,0 0,0 false

Install in this Direction

Install the rear door glass run LH to the rear door window division bar sub-assembly LH.

0,0 0,0 false

Install in this Direction

Insert the rear door window division bar sub-assembly LH with rear door glass run LH into the rear door panel assembly in the direction indicated by the arrow shown in the illustration.

0,0 0,0 false

Pull back in this Direction

Pull back part of the rear door weatherstrip LH and install the screw as shown in the illustration.

0,0 0,0 false

	Install in this Direction (1)
	Install in this Direction (2)

Install the rear door glass run LH as shown in the illustration.

HINT:

Install the rear door glass run LH so that the top of it aligns with the top of the rear door window division bar sub-assembly.

0,0 0,0 false

	Install in this Direction (1)
	Install in this Direction (2)

Attach the guide and install the rear door frame garnish LH in the direction indicated by the arrows, in the order shown in the illustration.

2.438,1.938 2.76,2.24 0.323,0.302 2.354,2.385 2.677,2.688 0.323,0.302 2.51,2.521 2.177,2.125 2.177,2.125 2.542,2.104 true 1.99,1.969 2.177,2.146 0.188,0.177 10 true *a

*a	Reference Point
	Butyl Tape

Apply new butyl tape to the rear door panel.

HINT:

·

Begin applying the butyl tape from the reference point shown in the illustration.

·

The butyl tape can be applied from either reference point.

2.354,0.938 2.677,0.615 true 1.823,1.292 2.135,1.042 true 2.698,0.49 2.927,0.698 0.229,0.208 10 true *1 1.563,1.25 1.792,1.458 0.229,0.208 10 true *2

*1	Rear Door Lock Remote Control Cable Assembly
*2	Rear Door Inside Locking Cable Assembly
	Install in this Direction

Pass the rear door lock remote control cable assembly and rear door inside locking cable assembly through a new rear door service hole cover LH.

0.302,0.292 0.5,0.49 0.198,0.198 10 true *a 3.01,0.333 3.208,0.531 0.198,0.198 10 true *a 0.51,3.094 0.708,3.292 0.198,0.198 10 true *a

*a	Reference Point
	Butyl Tape

Align the top of the rear door service hole cover LH with the reference point on the rear door panel and install it.

0,0 0,0 false

Install in this Direction

Install the rear door rear belt seal LH as shown in the illustration.

0,0 0,0 false

Install in this Direction

Attach the guide and install part of the rear door weatherstrip LH with the clip.

0,0 0,0 false

Install in this Direction

Install the rear door front belt seal LH to the rear door inner glass weatherstrip LH as shown in the illustration.

0,0 0,0 false

Install in this Direction

Install the rear door inner glass weatherstrip LH with rear door front belt seal LH as shown in the illustration.

0,0 0,0 false

Install in this Direction

Attach the guide and install part of the rear door weatherstrip LH with the clip.

0,0 0,0 false

Install in this Direction

Temporarily install the rear door inside handle sub-assembly LH in the direction indicated by the arrow as shown in the illustration.

Attach the claw and clamp to install the rear door inside handle sub-assembly LH.

1.969,0.833 2.229,0.385 true 2.375,1.698 2.01,1.333 true 2.271,0.26 2.479,0.469 0.208,0.208 10 true *1 2.438,1.635 2.646,1.844 0.208,0.208 10 true *2

*1	Rear Door Inside Locking Cable Assembly
*2	Rear Door Lock Remote Control Cable Assembly
	Install in this Direction

Attach the clamp and connect the rear door inside locking cable assembly and rear door lock remote control cable assembly to the rear door inside handle sub-assembly LH in the direction of the arrow indicated in the illustration.

0.281,1.458 0.417,1.646 0.135,0.188 10 true 2 2.719,1.094 2.854,1.281 0.135,0.188 10 true 3 2.854,1.677 2.99,1.865 0.135,0.188 10 true 1 2.302,1.125 2.438,1.313 0.135,0.188 10 true 4 1.917,1.115 2.052,1.302 0.135,0.188 10 true 5 1.542,1.156 1.677,1.344 0.135,0.188 10 true 6 1.167,1.167 1.302,1.354 0.135,0.188 10 true 7 0.74,1.146 0.875,1.333 0.135,0.188 10 true 8

Install in this Direction

Attach the claw and clip to install the rear door trim board sub-assembly LH in the direction indicated by the arrow shown in the illustration.

HINT:

Attach the claw and clip as shown in the illustration.

0,0 0,0 false

Install in this Direction

Attach the clip and install the 3 screws as shown in the illustration.

0,0 0,0 false

Install in this Direction

Attach the guide in the direction indicated by the arrow shown in the illustration.

0,0 0,0 false

Install in this Direction

Attach the guide and claw to install the rear power window regulator switch assembly with rear door armrest base panel.

0,0 0,0 false

Install in this Direction

Attach the guide in the direction indicated by the arrow shown in the illustration.

0.906,1.313 1.063,1.51 0.156,0.198 10 true 1 0.823,2.135 0.979,2.333 0.156,0.198 10 true 1 1.396,1.188 1.552,1.385 0.156,0.198 10 true 2 1.813,1.115 1.969,1.313 0.156,0.198 10 true 3 1.229,1.979 1.344,2.156 0.115,0.177 10 true 2 1.781,1.875 1.927,2.042 0.146,0.167 10 true 3 2.115,1 2.271,1.198 0.156,0.198 10 true 3 2.656,1.458 2.813,1.656 0.156,0.198 10 true 3 2.302,0.708 2.458,0.906 0.156,0.198 10 true 2 2.813,1.042 2.969,1.24 0.156,0.198 10 true 2 3.052,0.438 3.208,0.635 0.156,0.198 10 true 1

Install in this Direction

Attach the claw in the order shown in the illustration.

Attach the claw and install the rear door inside handle bezel LH.