RM36D0EC _59 Vehicle Exterior _083108 SLIDING ROOF / CONVERTIBLE _0402649 PANORAMIC MOON ROOF SYSTEM(for Gasoline Model) C

SLIDING ROOF / CONVERTIBLE  PANORAMIC MOON ROOF SYSTEM(for Gasoline Model)  B2342  Switch Failure  


DESCRIPTION

This DTC is stored when the sliding roof ECU (sliding roof drive gear assembly [sliding roof]) detects that the map light sub-assembly is stuck for 30 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2342 Switch Failure Sliding roof ECU (sliding roof drive gear assembly [sliding roof]) detects map light sub-assembly is stuck for 30 seconds or more.
·

Sliding roof ECU (sliding roof drive gear assembly [sliding roof])

·

Map light sub-assembly

·

Harness or connector



CAUTION / NOTICE / HINT

NOTICE:
·

If the sliding roof ECU (sliding roof drive gear assembly [sliding roof]) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear assembly [sliding roof]) must be initialized.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM (for Gasoline Model)>INITIALIZATION

·

The panoramic moon roof system uses the CAN and LIN communication systems. First, confirm that there are no malfunctions in the CAN and LIN communication systems. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

DTC B2342 is stored in the sliding roof ECU (sliding roof drive gear assembly [sliding roof]).



PROCEDURE

1.READ VALUE USING GTS (Switch Stuck)
a.

Read the Data List according to the display on the GTS.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM (for Gasoline Model)>DATA LIST / ACTIVE TEST

Body Electrical > Sliding Roof > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Current Roof Open Switch Stuck ON Sliding roof glass open switch stuck signal (Current) OFF or ON OFF: No sliding roof switch stuck signal (Current)
ON: Sliding roof switch stuck signal (Current) 		-
Current Roof Close Switch Stuck ON Sliding roof glass close switch stuck signal (Current) OFF or ON OFF: No sliding roof switch stuck signal (Current)
ON: Sliding roof switch stuck signal (Current) 		-
Past Roof Open Switch Stuck ON Sliding roof glass open switch stuck signal (Past) OFF or ON OFF: No sliding roof switch stuck signal (Past)
ON: Sliding roof switch stuck signal (Past) 		-
Past Roof Close Switch Stuck ON Sliding roof glass close switch stuck signal (Past) OFF or ON OFF: No sliding roof switch stuck signal (Past)
ON: Sliding roof switch stuck signal (Past) 		-
Current Vent Switch Stuck ON Sliding roof glass tilt switch stuck signal (Current) OFF or ON OFF: No sliding roof switch stuck signal (Current)
ON: Sliding roof switch stuck signal (Current) 		-
Past Vent Switch Stuck ON Sliding roof glass tilt switch stuck signal (Past) OFF or ON OFF: No sliding roof switch stuck signal (Past)
ON: Sliding roof switch stuck signal (Past) 		-
Body Electrical > Sliding Roof > Data List
Tester Display
Current Roof Open Switch Stuck ON
Current Roof Close Switch Stuck ON
Past Roof Open Switch Stuck ON
Past Roof Close Switch Stuck ON
Current Vent Switch Stuck ON
Past Vent Switch Stuck ON
50003 147 49,50,53,54,57,58
OK:

OFF appears on the GTS screen.



Result:
Result Proceed to
All items are displayed "OFF" A
In part or in whole item displayed "ON" B



A

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY [SLIDING ROOF])

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Panoramic Moon Roof)>REMOVAL


B

2.INSPECT MAP LIGHT SUB-ASSEMBLY
2.INSPECT MAP LIGHT SUB-ASSEMBLY
a.

Remove the map light sub-assembly.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL


b.

Inspect the map light sub-assembly.

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU [SLIDING ROOF DRIVE GEAR ASSEMBLY (SLIDING ROOF)] - MAP LIGHT SUB-ASSEMBLY AND BODY GROUND)

NG

REPLACE MAP LIGHT SUB-ASSEMBLY

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SWITCH ASSEMBLY>REMOVAL


3.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU [SLIDING ROOF DRIVE GEAR ASSEMBLY (SLIDING ROOF)] - MAP LIGHT SUB-ASSEMBLY AND BODY GROUND)
a.

Disconnect the P4 sliding roof ECU (sliding roof drive gear assembly [sliding roof]) connector.


b.

Disconnect the P24 map light sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P4-4 (TILT) or P24-21 (B) - Body ground Always 10 kΩ or higher
P4-5 (UP) or P24-20 (UP) - Body ground Always 10 kΩ or higher
P4-8 (CLS) or P24-17 (CLS) - Body ground Always 10 kΩ or higher
P4-9 (DWN) or P24-19 (DOWN) - Body ground Always 10 kΩ or higher
P4-10 (OPN) or P24-18 (OPN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY [SLIDING ROOF])

Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING (for Panoramic Moon Roof)>REMOVAL


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR