RM36D0EC _59 Vehicle Exterior _083111 EXTERIOR PANELS / TRIM _0400751 FRONT BUMPER(for Type A) A

EXTERIOR PANELS / TRIM FRONT BUMPER(for Type A) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front bumper assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure	Necessary Procedures	Effect/Inoperative Function when Necessary Procedures are not Performed	Link
Front bumper assembly (Including removal and installation)	Front television camera view adjustment	Panoramic view monitor system	(202304,999999,_56,_083082,_0586733,RM1000000029R9F,)
· Front television camera assembly, radiator grille assembly or front bumper assembly · Rear television camera assembly · Side television camera assembly LH or outer rear view mirror assembly LH · Side television camera assembly RH or outer rear view mirror assembly RH	Television camera view adjustment (Adjustment of all cameras) HINT: Replacement or removal and installation of 2 or more parts	Panoramic view monitor system	(202304,999999,_56,_083082,_0586733,RM1000000029R9F,)

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure	Necessary Procedures	Effect/Inoperative Function when Necessary Procedures are not Performed	Link
Front bumper assembly (Including removal and installation)	Front television camera view adjustment	Panoramic view monitor system	(202304,999999,_56,_083082,_0586733,RM1000000029R9F,)
· Front television camera assembly, radiator grille assembly or front bumper assembly · Rear television camera assembly · Side television camera assembly LH or outer rear view mirror assembly LH · Side television camera assembly RH or outer rear view mirror assembly RH	Television camera view adjustment (Adjustment of all cameras) HINT: Replacement or removal and installation of 2 or more parts	Panoramic view monitor system	(202304,999999,_56,_083082,_0586733,RM1000000029R9F,)

HINT:: ·

When the front bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform millimeter wave radar sensor adjustment.

-

Driving Adjustment:

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT202304,202405,_51,_083055,_0401007,RM1000000029L6F,202405,202409,_51,_083055,_0401007,RM100000002ME7H,202409,999999,_51,_083055,_0401007,RM100000002NTD7,

-

Target Adjustment (Triangle Target):

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)202304,202405,_51,_083055,_0401007,RM1000000029L6G,202405,202409,_51,_083055,_0401007,RM100000002ME7I,202409,999999,_51,_083055,_0401007,RM100000002NTD8,

-

Target Adjustment (Flat Surface Target):

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)202304,202405,_51,_083055,_0401007,RM1000000029L6H,202405,202409,_51,_083055,_0401007,RM100000002ME7K,202409,999999,_51,_083055,_0401007,RM100000002NTDA,

PROCEDURE

Hide Display 53896B 1.REMOVE FRONT FENDER FRONT SPLASH SHIELD LH

Click hereVehicle Exterior>DOOR / HATCH>HOOD LOCK CONTROL CABLE ASSEMBLY>REMOVAL202004,999999,_59,_083093,_0403686,RM100000001MECO_01_0005,

Hide Display 53895B 2.REMOVE FRONT FENDER FRONT SPLASH SHIELD RH

HINT:: Use the same procedure described for the LH side.

Hide Display 75602A 3.REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY LH

0,0 0,0 false

	Screw
	Clip

Remove the screw.

Remove the 2 clips.

0,0 0,0 false

Protective Tape

Put protective tape around the front fender moulding sub-assembly LH.

0,0 0,0 false

	Place Hand Here
	Remove in this Direction(1)
	Remove in this Direction(2)

Pull back the edge of the front fender liner LH and detach the claw by pushing the area indicated by the arrow in the illustration with a finger.

NOTICE:: ·

Do not apply excessive force when pulling back the front fender liner LH.

·

To avoid damaging the claws, do not forcibly pull the front fender moulding sub-assembly LH.

0,0 0,0 false

	Place Hand Here
	Remove in this Direction

Detach the clip and disconnect the front fender moulding sub-assembly LH as shown in the illustration.

Hide Display 75601A 4.REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH

HINT:: Use the same procedure described for the LH side.

Hide Display 5.REMOVE FRONT BUMPER ASSEMBLY

0,0 0,0 false

Protective Tape

Apply protective tape around the front bumper assembly.

HINT:: Use the same procedure on the other side.

Remove the 4 bolts.

Remove the 6 screws.

Remove the 2 clips.

HINT:: Use the same procedure on the other side.

0,0 0,0 false

	Place Hand Here
	Remove in this Direction

Place your hand at the positions shown in the illustration and pull in the removal direction to detach the claw.

HINT:: Use the same procedure on the other side.

Pull back the edge of the front fender liner LH and disconnect the 2 connectors.

0,0 0,0 false

Remove in this Direction

Detach the claw and remove the front bumper assembly.

Remove the 2 clips from the front fender moulding sub-assembly LH.

NOTICE:: If the front bumper assembly has been removed, replace the clip with a new one.

HINT:: Use the same procedure on the other side.