REAR SUSPENSION  REAR STABILIZER BAR  INSTALLATION  

0.948,0.75 1.031,0.583 1.031,0.583 1.281,0.583 false 0.802,0.896 0.885,1.229 0.885,1.229 1.052,1.229 true 2.875,1.146 2.792,0.979 2.792,0.979 2.542,0.979 false 2.948,1.333 2.865,1.667 2.865,1.667 2.698,1.667 true 1.094,1.177 1.427,1.51 0.333,0.333 10 false *b 1.323,0.531 1.74,0.781 0.417,0.25 10 false *a 2.375,0.906 2.792,1.156 0.417,0.25 10 false *a 2.531,1.604 2.865,1.938 0.333,0.333 10 false *b

*a	Stopper
*b	Cutout

Install the 2 rear stabilizer bushings to the outside of the stoppers on the rear stabilizer bar.

NOTICE:

Be sure to install the rear stabilizer bushings so that each cutout faces the front of the vehicle.

HINT:

The cutout of the rear stabilizer bushing can be positioned either up or down.

2.417,2.792 2.583,2.542 2.583,2.542 2.75,2.542 true 2.792,2.49 3.042,2.74 0.25,0.25 10 false *a

*a	Arrow Mark
	Upper of the Vehicle

Install the rear No. 1 stabilizer bar bracket LH to the rear stabilizer bushing.

NOTICE:

Be sure to install the rear No. 1 stabilizer bar bracket LH so that each arrow mark faces the upper of the vehicle.

Install the 2 rear lower stabilizer brackets to the rear stabilizer bushing.

0.417,0.167 0.583,0.333 0.167,0.167 10 true A 2.917,0.167 3.083,0.333 0.167,0.167 10 true A 2.958,1.458 3.125,1.625 0.167,0.167 10 true B 0.438,1.458 0.604,1.625 0.167,0.167 10 true B

Install the rear stabilizer bar, rear No. 1 stabilizer bar bracket LH, rear No. 1 stabilizer bar bracket RH, rear No. 2 stabilizer bar bracket LH, rear No. 2 stabilizer bar bracket RH and 2 rear stabilizer bushings to the rear suspension member sub-assembly with the 4 bolts.

Torque:

78 N*m (795 kgf*cm, 58 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A) and then fully tighten the 2 bolts in the order of (B) and (A).

1.333,2.958 1.667,3.208 0.333,0.25 10 false *a 1.271,0.094 1.458,0.281 0.188,0.188 10 true A 2.25,1.813 2.438,2 0.188,0.188 10 true B

*a	Torque Wrench Fulcrum Length

Using a ball joint lock nut wrench, install the rear stabilizer link assembly LH with the nut (A).

Torque:

100 N*m (1020 kgf*cm, 74 ft.*lbf)

HINT:

·

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.

·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION201910,999999,_V1,_083040,_0402303,RM100000001JHCH,

·

When using a ball joint lock nut wrench (fulcrum length of 159 mm (6.260 in.)) + torque wrench (fulcrum length of 400 mm (15.748 in.)):

71.6 N*m (730 kgf*cm, 53 ft.*lbf)