RM36D0EC _59 Vehicle Exterior _083111 EXTERIOR PANELS / TRIM _0400760 ROCKER PANEL MOULDING A

EXTERIOR PANELS / TRIM ROCKER PANEL MOULDING REMOVAL

CAUTION / NOTICE / HINT

HINT:: ·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.

PROCEDURE

Hide Display 76902A 1.REMOVE SIDE MUDGUARD SUB-ASSEMBLY LH

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>SIDE MUDGUARD>REMOVAL201910,999999,_59,_083111,_0400756,RM100000001J9LU,

Hide Display 65632D 2.REMOVE REAR WHEEL FRONT HOUSE PLATE LH

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR WHEEL HOUSE PLATE>REMOVAL201910,999999,_59,_083111,_0400772,RM100000001J9NN,

Hide Display 75874 3.REMOVE QUARTER PANEL WHEEL OPENING MOULDING LH

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>WHEEL OPENING MOULDING (for Rear)>REMOVAL201910,202304,_59,_083111,_0400767,RM100000001J9N1,202304,999999,_59,_083111,_0400767,RM1000000029RRU,

Hide Display 75852 4.REMOVE ROCKER PANEL MOULDING LH

Put protective tape around the rocker panel moulding LH.

0,0 0,0 false

Protective Tape

Remove the 2 screws.

Remove the 2 clips labeled A.

3.344,3.594 3.344,3.979 true 3.135,3.49 3.135,3.875 true 2.896,3.375 2.896,3.76 true 2.563,3.219 2.563,3.604 true 2.25,3.063 2.25,3.448 true 1.896,2.896 1.896,3.281 true 1.438,2.667 1.438,3.052 true 1.063,2.521 1.063,2.906 true 0.688,2.344 0.688,2.729 true 3.594,3.708 3.594,4.094 true 0.604,2.75 0.76,2.938 0.156,0.188 10 true *a 0.99,2.885 1.146,3.073 0.156,0.188 10 true *a 1.354,3.052 1.51,3.24 0.156,0.188 10 true *b 1.813,3.281 1.969,3.469 0.156,0.188 10 true *b 2.167,3.448 2.323,3.635 0.156,0.188 10 true *b 2.479,3.604 2.635,3.792 0.156,0.188 10 true *b 2.813,3.76 2.969,3.948 0.156,0.188 10 true *b 3.063,3.875 3.219,4.063 0.156,0.188 10 true *b 3.26,3.979 3.417,4.167 0.156,0.188 10 true *b 3.51,4.094 3.667,4.281 0.156,0.188 10 true *b

*a	Clip A	*b	Clip B
	Insert Screwdriver Here		Remove in this Direction (1)
	Remove in this Direction (2)		Remove in this Direction (3)
	Protective Tape	-	-

Remove the 8 clips labeled B.

Using a screwdriver with its tip wrapped with protective tape, detach the claw as shown in the illustration.

ii.

Using needle-nose pliers, detach the claw to remove the clip B as shown in the illustration.

Detach the clip and remove the rocker panel moulding LH in the order shown in the illustration.

1.542,1.229 1.76,1.417 0.219,0.188 10 true (1) 2.344,1.073 2.563,1.26 0.219,0.188 10 true (2) 2.823,0.99 3.042,1.177 0.219,0.188 10 true (3) 3.26,0.917 3.479,1.104 0.219,0.188 10 true (4) 3.698,0.833 3.917,1.021 0.219,0.188 10 true (5) 4.292,0.708 4.51,0.896 0.219,0.188 10 true (6) 4.74,0.625 4.958,0.813 0.219,0.188 10 true (7) 5.198,0.552 5.417,0.74 0.219,0.188 10 true (8) 5.625,0.458 5.844,0.646 0.219,0.188 10 true (9)

Place Hand Here

Remove in this Direction

Using a clip remover, remove the grommet.

HINT:: Use the same procedure for both grommets.