RM3660EC _58 Vehicle Interior _080793 METER / GAUGE / DISPLAY _0473175 METER / GAUGE SYSTEM(for 12.3 Inch Display) J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM(for 12.3 Inch Display)  Hybrid System Indicator Malfunction  


DESCRIPTION

A hybrid system indicator has been included on this vehicle. In this circuit, the combination meter assembly receives the hybrid system indicator signal from the hybrid vehicle control ECU via CAN communication. The combination meter assembly controls the operation of the hybrid system indicator according to the hybrid system indicator signal received from the hybrid vehicle control ECU via CAN communication.

WIRING DIAGRAM

E370855E25
0.677,2.271 3.042,2.521 2.365,0.25 10 false : CAN Communication Line 0.958,1.583 2.802,2.042 1.844,0.458 10 false Hybrid Vehicle Control ECU 4.677,1.563 6.656,1.969 1.979,0.406 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

When replacing any of the following ECUs, update the ECU security key.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY

-

Combination meter assembly

-

Hybrid vehicle control ECU


·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK FOR DTC (HYBRID CONTROL SYSTEM)

B

GO TO CAN COMMUNICATION SYSTEM

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING


2.CHECK FOR DTC (HYBRID CONTROL SYSTEM)
a.

Check if hybrid control system DTCs are output.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.READ VALUE USING GTS

B

GO TO HYBRID CONTROL SYSTEM

PA10 HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>PA10 HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>DIAGNOSTIC TROUBLE CODE CHART

PB10 HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>PB10 HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>DIAGNOSTIC TROUBLE CODE CHART


3.READ VALUE USING GTS
a.

Using the GTS, read the Data List.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
HV/EV System Indicator Hybrid system indicator value Min.: -512%, Max.: 511% or Unset Current hybrid system indicator status "Unset" is displayed when the vehicle is stopped and the ignition switch is ON
Body Electrical > Combination Meter > Data List
Tester Display
HV/EV System Indicator
50003 409 66
OK:

Hybrid system indicator value displayed on the GTS is almost the same as the hybrid system indicator indication.



Result:
Proceed to
OK
NG



OK

GO TO HYBRID CONTROL SYSTEM

PA10 HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>PA10 HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>HOW TO PROCEED WITH TROUBLESHOOTING

PB10 HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY): Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>PB10 HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY)>HOW TO PROCEED WITH TROUBLESHOOTING


NG

REPLACE COMBINATION METER ASSEMBLY

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL