RM3660EC _52 Drivetrain _080786 AXLE AND DIFFERENTIAL _0392697 FRONT AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front axle hub bolt removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: The vehicle height changes because of tire replacement.

Tires Rear television camera assembly optical axis (Back camera position setting)* Parking Assist Monitor System (Click here)
Parking assist ECU initialization Panoramic View Monitor System (Click here)

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: The vehicle height changes because of tire replacement.

Tires Rear television camera assembly optical axis (Back camera position setting)* Parking Assist Monitor System (Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 2.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

a.

Remove the 2 bolts and separate the front disc brake caliper assembly from the steering knuckle.

NOTICE:

Use wire or an equivalent tool to keep the front disc brake caliper assembly from hanging by the front flexible hose.



Hide 43502D 4.REMOVE FRONT AXLE HUB BOLT

a.
C398402C01
2.156,0.802 2.844,0.802 2.844,0.802 2.844,1.208 true 2.396,1.01 2.833,1.01 true 1.958,0.24 1.688,0.24 1.688,0.24 1.688,0.896 true 2.76,1.208 3.073,1.406 0.313,0.198 10 false *a 2.021,0.167 2.344,0.333 0.323,0.167 10 true SST
*a Service Nut


Temporarily install 2 service nuts to the front axle hub bolts as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


NOTICE:

Install the service nuts to prevent damage to the front axle hub bolts.



b.

Using SST and a screwdriver or an equivalent tool to hold the front axle hub sub-assembly, remove the front axle hub bolt.

SST
09611-12010  

NOTICE:

Do not damage the threads of the front axle hub bolts.



Hide 43502D 5.INSTALL FRONT AXLE HUB BOLT

a.

Temporarily install a new front axle hub bolt to the front axle hub sub-assembly.


b.
C398403C01
0.927,0.458 1.792,0.458 true 0.688,1.542 0.688,0.792 true 1.833,0.375 2.021,0.552 0.188,0.177 10 true *a 0.615,1.563 0.927,1.76 0.313,0.198 10 true *b
*a Service Nut
*b Washer


Install a washer and service nut to the front axle hub bolt as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


HINT:

Recommended washer thickness is 5 mm (0.197 in.) or more.



c.

Using a screwdriver or an equivalent tool to hold the front axle hub sub-assembly, install the front axle hub bolt by tightening the service nut.

NOTICE:
·

Install the service nuts to prevent damage to the front axle hub bolts.

·

Do not damage the threads of the front axle hub bolts.




d.

Remove the 3 service nuts and washer from the 3 front axle hub bolts.


Hide 7.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

a.

Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

Torque:
107 N*m (1091 kgf*cm, 79 ft.*lbf)

NOTICE:
·

Do not twist the front flexible hose when installing the front disc brake caliper assembly.

·

Make sure that there is no foreign matter on the threads of the bolt.