RM3660EC _56 Audio / Visual / Telematics _080751 AUDIO / VIDEO _0599626 AUDIO AND VISUAL SYSTEM(for 10.25 Inch Display) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for 10.25 Inch Display)  Noise Occurs only for Radio  


CAUTION / NOTICE / HINT

HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for 10.25 Inch Display)>PRECAUTION


PROCEDURE

1.CHECK CONDITIONS AROUND THE TIME THE PROBLEM OCCURRED
a.

Check for situations/locations when noise occurs.


Result:
Result Proceed to
Noise occurs in all areas A
Noise occurs in specific areas B



A

2.CHECK FOR ADDITIONAL DEVICES (SUNSHADE FILM, TELECOMMICATIONS ANTENNAS, ETC)

B

RADIO WAVES ARE DISTURBED (RADIO WAVE ENVIRONMENT, ETC. EXTERNAL FACTOR)

2.CHECK FOR ADDITIONAL DEVICES (SUNSHADE FILM, TELECOMMICATIONS ANTENNAS, ETC)
a.

Check that there is no sunshade film or additional devices such as a telecommunications antenna installed.

OK:

AFTERMARKET DEVICES (INCLUDING NON-GENUINE WIRING) ARE NOT INSTALLED


HINT:

The vehicle is equipped with noise filters that prevent other systems in the vehicle from affecting the radio. Therefore, the system will not be affected by large interference. If the system is affected by large interference, confirm that no non-standard wire harnesses are installed, all of the noise filters are installed correctly, and the mount of the antenna is correctly earthed.



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

AFTERMARKET DEVICES ARE THE NOISE SOURCE

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Disconnect the connector (E) from the radio and display receiver assembly. Then operate the radio and display receiver assembly again to check for noise.


Result:
Result Proceed to
Noise does not occur A
Noise occurs B



A

4.CHECK INSTALLATION OF ANTENNA EARTH

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


4.CHECK INSTALLATION OF ANTENNA EARTH
a.

Make sure that the mount of the antenna cord sub-assembly is earthed securely to the vehicle body.

OK:

Installation is normal



Result:
Proceed to
OK
NG



OK

5.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY (DISCONNECT CONNECTOR)

NG

PROPERLY INSTALL ANTENNA EARTH

5.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY (DISCONNECT CONNECTOR)
a.

With the connector between the No. 3 antenna cord sub-assembly and No. 1 amplifier antenna assembly disconnected, operate the radio and display receiver assembly again and check for noise.


Result:
Result Proceed to
Noise occurs A
Noise does not occur B



A

6.INSPECT NO. 1 AMPLIFIER ANTENNA ASSEMBLY (DISCONNECT CONNECTOR)

B

REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL


6.INSPECT NO. 1 AMPLIFIER ANTENNA ASSEMBLY (DISCONNECT CONNECTOR)
a.

With the connector between the No. 1 amplifier antenna assembly and No. 2 antenna cord sub-assembly disconnected, operate the radio and display receiver assembly again and check for noise.


Result:
Result Proceed to
Noise occurs A
Noise does not occur B



A

7.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY (DISCONNECT CONNECTOR)

B

REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL


7.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY (DISCONNECT CONNECTOR)
a.

With the connector between the No. 2 antenna cord sub-assembly and antenna cord sub-assembly disconnected, operate the radio and display receiver assembly again and check for noise.


Result:
Result Proceed to
Noise occurs A
Noise does not occur B



A

REPLACE ANTENNA CORD SUB-ASSEMBLY

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL


B

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL