By using Partial Lift Fuel Injection Control to spray fuel before the needle inside each direct fuel injector assembly has fully opened, the injection of fuel by the direct fuel injector assembly can be precisely controlled at partial lift. Due to the influence on the injected fuel volume due to wear and variations between injectors, feedback control is implemented for partial lift fuel injection.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Note |
|---|---|---|---|---|---|
| P02EE00 | Cylinder 1 Injector Circuit Range/Performance | The No. 1 cylinder partial lift control learned value exceeds the threshold (2 trip detection logic). | ·
Direct fuel injector assembly (No. 1 cylinder) ·
Fuel pressure sensor (for high pressure side) ·
Open or short in direct fuel injector assembly circuit ·
ECM |
Comes on | SAE Code: P02EE |
| P02EF00 | Cylinder 2 Injector Circuit Range/Performance | The No. 2 cylinder partial lift control learned value exceeds the threshold (2 trip detection logic). | ·
Direct fuel injector assembly (No. 2 cylinder) ·
Fuel pressure sensor (for high pressure side) ·
Open or short in direct fuel injector assembly circuit ·
ECM |
Comes on | SAE Code: P02EF |
| P02F000 | Cylinder 3 Injector Circuit Range/Performance | The No. 3 cylinder partial lift control learned value exceeds the threshold (2 trip detection logic). | ·
Direct fuel injector assembly (No. 3 cylinder) ·
Fuel pressure sensor (for high pressure side) ·
Open or short in direct fuel injector assembly circuit ·
ECM |
Comes on | SAE Code: P02F0 |
| P02F100 | Cylinder 4 Injector Circuit Range/Performance | The No. 4 cylinder partial lift control learned value exceeds the threshold (2 trip detection logic). | ·
Direct fuel injector assembly (No. 4 cylinder) ·
Fuel pressure sensor (for high pressure side) ·
Open or short in direct fuel injector assembly circuit ·
ECM |
Comes on | SAE Code: P02F1 |
| DTC No. | Data List |
|---|---|
| P02EE00 | ·
Target Fuel Pressure (High) ·
Fuel Pressure (High) ·
High Fuel Pressure Sensor ·
High Pressure Fuel Pump Duty Ratio (D4) ·
High Pressure Fuel Pump Discharge Rate ·
Injection Mode ·
Injection Timing Cylinder #1 (D4) ·
Injection Time Cylinder #1 (D4) |
| P02EF00 | |
| P02F000 | |
| P02F100 |
The ECM calculates the partial lift control learning value for each cylinder. The ECM counts the number of times that the partial lift control learned value exceeds the threshold, and if the total number exceeds the threshold, the ECM determines that partial lift control is malfunctioning and illuminates the MIL and stores a DTC.
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature is 75°C [167°F] or higher [A].
Turn the ignition switch off and wait for at least 30 seconds [B].
Start the engine and wait for at least 5 minutes [C].
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes [D].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P02EE00, P02EF00, P02F000 or P02F100.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
If the judgment result is INCOMPLETE, perform steps [A] through [D] again.
[A] to [D]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P02EE00, P02EF00, P02F000 and/or P02F100 is output | A |
| DTC P02EE00, P02EF00, P02F000 and/or P02F100 and other DTCs are output | B |
If any DTCs other than P02EE00, P02EF00, P02F000 and/or P02F100 are output, troubleshoot those DTCs first.
A
B
Read the DTCs.
| Result | Proceed to |
|---|---|
| Only 1 DTC among DTC P02EE00, P02EF00, P02F000 and P02F100 is output | A |
| 2 or more DTCs among DTC P02EE00, P02EF00, P02F000 and P02F100 are output | B |
If the malfunction occurred for one cylinder or multiple cylinders can be determined based on the stored DTCs.
A
B
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C141-16 (#1D+) - C141-17 (#1D-) | 20°C (68°F) | 1.34 to 1.64 Ω |
| C141-11 (#2D+) - C141-10 (#2D-) | 20°C (68°F) | 1.34 to 1.64 Ω |
| C141-12 (#3D+) - C141-13 (#3D-) | 20°C (68°F) | 1.34 to 1.64 Ω |
| C141-15 (#4D+) - C141-14 (#4D-) | 20°C (68°F) | 1.34 to 1.64 Ω |
| C141-16 (#1D+) or C141-17 (#1D-) - Body ground and other terminals | Always | 1 MΩ or higher |
| C141-11 (#2D+) or C141-10 (#2D-) - Body ground and other terminals | Always | 1 MΩ or higher |
| C141-12 (#3D+) or C141-13 (#3D-) - Body ground and other terminals | Always | 1 MΩ or higher |
| C141-15 (#4D+) or C141-14 (#4D-) - Body ground and other terminals | Always | 1 MΩ or higher |
The standard values shown are direct fuel injector assembly resistance values.
If the measured resistance value differs from the other cylinders and the injector resistance is normal, check the related cylinder as a poorly connected connector is suspected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the resistance of the direct fuel injector assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher).
Enter the following menus.
| Active Test Display |
|---|
| Control the Injection Mode |
| Data List Display |
|---|
| Coolant Temperature |
| Injection Mode |
| Short FT B1S1 |
| Long FT B1S1 |
According to the display on the GTS, read the Data List with the Active Test "Control the Injection Mode" set to Direct.
| Item | Proceed to | |
|---|---|---|
| Injection Mode | Short FT B1S1 + Long FT B1S1 | |
| Direct | -25% or less, or +25% or higher | A |
| Between -25% and +25% | B | |
A
B
Replace the fuel pressure sensor (for high pressure side).
Perform "Inspection After Repair" after replacing the fuel pressure sensor (for high pressure side).
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P02EE00, P02EF00, P02F000 and/or P02F100 is output | B |
Perform "Inspection After Repair" after replacing the direct fuel injector assembly.
A
B
Replace the direct fuel injector assembly.
Perform "Inspection After Repair" after replacing the direct fuel injector assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P02EE00, P02EF00, P02F000 and/or P02F100 is output | B |
A
B
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Read the DTCs.
DTCs are not output.
| Proceed to |
|---|
| NEXT |
NEXT