MALFUNCTION DESCRIPTION
The main CPU and sub CPU of the hybrid vehicle control ECU monitor their internal operation and each other for malfunctions.
The cause of this malfunction may be the following:
Hybrid vehicle control ECU malfunction
Discrepancy between motor resolver signal and actual vehicle speed
The hybrid vehicle control ECU monitors its internal operation and will store these DTCs when it detects an internal malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate | Note |
|---|---|---|---|---|---|---|
| P060A94 | Hybrid/EV Powertrain Control Module Monitoring Processor Unexpected Operation | ·
The sub CPU value received by the main CPU of the hybrid vehicle control ECU exceeds the threshold for a certain period of time. ·
The hybrid vehicle control ECU detects an internal malfunction due to an abnormal calculation or sensor malfunction. (1 trip detection logic) |
Hybrid vehicle control ECU | Comes on | Master Warning:
Comes on |
SAE Code:
P060A |
The hybrid vehicle control ECU monitors its internal operation. If the internal operation is malfunctioning, the hybrid vehicle control ECU illuminates the MIL and stores a DTC.
| Related DTCs | P060A (INF P060A94): Internal control module monitoring processor performance |
| Required sensors/components | Hybrid vehicle control ECU |
| Frequency of operation | Continuous |
| Duration | TMC's intellectual property |
| MIL operation | 1 driving cycle |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not stored | TMC's intellectual property |
| Other conditions belong to TMC's intellectual property | - |
| TMC's intellectual property | - |
| Hybrid vehicle control ECU | DTC P060A (INF P060A94) is not detected |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON and turn the GTS on.
Turn the ignition switch to ON (READY) and wait for 10 seconds or more. [*1]
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform the normal judgment procedure again.
P060A94 may be output as a result of the malfunction indicated by the DTCs in table below.
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Sensor and actuator circuit malfunction | Motor generator control system | P0A3F16 | Drive Motor "A" Position Sensor Circuit Voltage Below Threshold |
| P0A3F21 | Drive Motor "A" Position Sensor Signal Amplitude < Minimum | ||
| P0A3F22 | Drive Motor "A" Position Sensor Signal Amplitude > Maximum | ||
Check for DTCs.
| Result | Proceed to |
|---|---|
| Electronically Controlled Brake System DTCs are not output | A |
| Electronically Controlled Brake System DTCs are output | B |
Turn the ignition switch off.
A
B
Check for DTCs.
| Result | Proceed to |
|---|---|
| P060A94 only is output. | A |
| DTCs except P060A94 are output. | B |
Turn the ignition switch off.
A
B
Read the Freeze Frame Data of DTC P060A94.
| Result | Proceed to |
|---|---|
| Vehicle was stopped ("FR Wheel Speed" and "FL Wheel Speed" are between 0 and 1.4 km/h (0 and 1 mph)) but "Vehicle Speed" was 3 km/h (2 mph) or more | A |
| Vehicle was stopped ("FR Wheel Speed" and "FL Wheel Speed" are between 0 and 1.4 km/h (0 and 1 mph)) and "Vehicle Speed" was less than 3 km/h (2 mph) | B |
Turn the ignition switch off.
A
For the inspection method of the motor resolver circuit, refer to DTC P0A3F16.
B