DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Collision System / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Total Distance Traveled | Total Distance Traveled | Min.: 0, Max.: 16777215 | Equivalent to the actual total driving distance | Cannot be used |
| Total Distance Traveled - Unit | Total Distance Traveled - Unit | km or mile | Units according destination | Cannot be used |
| PCS Function ON/OFF State | Pre-collision system on/off status | ON or OFF | ON: Pre-collision system on
OFF: Pre-collision system off |
- |
| PBA Request | Pre-collision brake assist operation status | Not PBA Request, PBA Standby Request, PBA Request Level 1, PBA Request Level 2 | Not PBA Request: Pre-collision brake assist not operating
PBA Standby Request: Pre-collision brake assist operating and brake pedal not depressed PBA Request Level 1: Pre-collision brake assist operating and brake pedal depressed PBA Request Level 2: Pre-collision brake assist operating and brake pedal deeply depressed |
The value varies according to the possibility of a collision. The pre-collision brake assist request only indicates the status that the assist preparation is necessary. Whether or not the assist control is actually performed is dependent upon how the driver depresses the brake. |
| VGRS Activation Request | VGRS control activation request | Not Request, VGRS 1 Request, VGRS 2 Request, VGRS 3 Request | Not Request: No request
VGRS 1 Request: Request 1 VGRS 2 Request: Request 2 VGRS 3 Request: Request 3 |
Cannot be used |
| Warning Brake Request | Warning brake request status | ON or OFF | ON: Warning brake request on
OFF: Warning brake request off |
Cannot be used |
| FPB Request | PCS brake request to skid control ECU (pre-collision braking) | ON or OFF | ON: Operating
OFF: Not operating |
- |
| PB Request | Pre-collision brake operation status | ON or OFF | ON: Operating
OFF: Not operating |
- |
| AVS Control Request | AVS operation status | ON or OFF | ON: Operating
OFF: Not operating |
Cannot be used |
| Prefill | PCS brake operation preparation to skid control ECU | ON or OFF | ON: Operating
OFF: Not operating |
- |
| PBR Request | PBR operation status | ON or OFF | ON: Operating
OFF: Not operating |
- |
| PBH Request | PBH operation status | ON or OFF | ON: Operating
OFF: Not operating |
- |
| LPB Request | LPB request status | ON or OFF | ON: Operating
OFF: Not operating |
- |
| PCS PBA Invalid | Pre-collision brake assist function status | ON or OFF | ON: Pre-collision brake assist function valid
OFF: Pre-collision brake assist function invalid |
- |
| PCS Warning Buzzer Invalid | PCS warning buzzer function status | ON or OFF | ON: PCS warning buzzer function valid
OFF: PCS warning buzzer function invalid |
- |
| PCS PB Invalid | PCS brake function status | ON or OFF | ON: PCS brake function valid
OFF: PCS brake function invalid |
- |
| Acceleration Suppression at Low Speed (A Control) Invalid | - | - | - | Cannot be used |
| Emergency Steering Assist Invalid 1 | Emergency steering assist invalid 1 status | ON or OFF | ON: Emergency steering assist invalid 1 function invalid
OFF: Emergency steering assist invalid 1 function valid |
- |
| PCS Warning Display Request | PCS warning sensitivity display status | Not Request, PCS Warning Display 1 Request, PCS Warning Display 2 Request, PCS Warning Display 3 Request | Not Request: No display
PCS Warning Display 1 Request: Display Early PCS Warning Display 2 Request: Display Middle PCS Warning Display 3 Request: Display Late |
"BRAKE!" is displayed on multi-information display. |
| PCS Warning Buzzer Request | PCS warning buzzer (meter buzzer) status | ON or OFF | ON: PCS warning buzzer sounding
OFF: PCS warning buzzer not sounding |
- |
| Vehicle Information (Conv/HV/EV) | Vehicle Information (Conv/HV/EV) | Unknown, Conv, HV/EV | Unknown: Vehicle information not confirmed
Conv: Conventional HV/EV: Hybrid vehicle |
- |
| Vehicle Information (Powertrain Type) | Vehicle information (powertrain type) | Unknown, Conv, S&S, HV, PHV, EV, 1Motor HV, FCV | - | - |
| Vehicle Information (Transmission Type) | Vehicle information (transmission type) | MT, AT, CVT, MMT, SMT, HV/EV - AT or Unknown | Displays the type of transmission | - |
| Power Steering Control Module Equipped Information | Power steering control module is installed or not | Absence or Presence | Presence: Equipped | - |
| VGRS ECU Equipped Information | Variable gear ratio steering system function availability | Unknown, Absence or Presence | Unknown: Vehicle information not confirmed
Absence: Variable gear ratio steering system absence Presence: Variable gear ratio steering system presence |
Cannot be used |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Collision System / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| PCS Warning Buzzer | Sounds the meter buzzer | Active / Not Active | Test possible with ignition switch ON and vehicle stopped |