DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Front SW Auto Operation | Sliding roof glass auto operation function | OFF or ON | Customize setting displayed | - |
| Hall IC1 Pulse | Hall IC1 pulse output | Lo or Hi | Lo and Hi repeat during motor operation | Lo: Hall IC1 output is low
Hi: Hall IC1 output is high |
| Hall IC1 Status | Status of Hall IC1 | Normal or Error | Normal: Hall IC1 normal
Error: Hall IC1 not normal |
- |
| Hall IC2 Pulse | Hall IC2 pulse output | Lo or Hi | Lo and Hi repeat during motor operation | Lo: Hall IC2 output is low
Hi: Hall IC2 output is high |
| Hall IC2 Status | Status of Hall IC2 | Normal or Error | Normal: Hall IC2 normal
Error: Hall IC2 not normal |
- |
| Ignition (MPX) | Ignition switch signal (LIN signal) | OFF or ON | OFF: Ignition switch off
ON: Ignition switch ON |
"OFF" is also displayed for this item when the ignition switch is turned ACC. |
| Hall IC1 Pulse(Shade) | Hall IC1 pulse output (shade) | Lo or Hi | Lo and Hi repeat during motor operation | Lo: Hall IC1 output is low
Hi: Hall IC1 output is high |
| Hall IC1 Status(Shade) | Hall IC1 pulse output (shade) | Lo or Hi | Lo and Hi repeat during motor operation | Lo: Hall IC1 output is low
Hi: Hall IC1 output is high |
| Hall IC2 Pulse(Shade) | Hall IC2 pulse output (shade) | Lo or Hi | Lo and Hi repeat during motor operation | Lo: Hall IC2 output is low
Hi: Hall IC2 output is high |
| Hall IC2 Status(Shade) | Status of Hall IC2 (shade) | Normal or Error | Normal: Hall IC2 normal
Error: Hall IC2 not normal |
- |
| Door Key Close Operation | Key-linked sliding roof glass close signal | OFF or ON | OFF: Driver door key cylinder not turned
ON: Driver door key cylinder turned and held at the lock position |
- |
| Door Key Open Operation | Key-linked sliding roof glass open signal | OFF or ON | OFF: Driver door key cylinder not turned
ON: Driver door key cylinder turned and held at the unlock position |
- |
| Wireless Close Operation | Wireless transmitter-linked sliding roof glass close signal | OFF or ON | OFF: Wireless transmitter lock switch not pressed
ON: Wireless transmitter lock switch pressed and held |
- |
| Wireless Open Operation | Wireless transmitter-linked sliding roof glass open signal | OFF or ON | OFF: Transmitter UNLOCK switch not pressed
ON: Transmitter UNLOCK switch pressed and held |
- |
| Key Off Permission | Key-off sliding roof glass operation permit signal | OFF or ON | OFF: Any status except "ON" status
ON: Front doors are not opened within 45 seconds after ignition switch turned off |
- |
| Vent Switch | TILT switch signal | OFF or ON | OFF: Tilt switch (UP/DOWN) on the tilt switch not pressed
ON: Tilt switch (UP/DOWN) on the tilt switch pressed |
- |
| Roof Open Switch | OPEN switch signal | OFF or ON | OFF: Slide switch (OPEN) on the slide switch not pressed
ON: Slide switch (OPEN) on the slide switch pressed |
- |
| Roof Close Switch | CLOSE switch signal | OFF or ON | OFF: Slide switch (CLOSE) on the slide switch not pressed
ON: Slide switch (CLOSE) on the slide switch pressed |
- |
| Shade Close Switch | Roof sunshade close switch signal | OFF or ON | OFF: Roof sunshade switch (close) not pressed
ON: Roof sunshade switch (open) pressed |
- |
| Shade Open Switch | Roof sunshade open switch signal | OFF or ON | OFF: Roof sunshade switch (open) not pressed
ON: Roof sunshade (open) switch pressed |
- |
| Current Roof Open Switch Stuck ON | Sliding roof glass open switch stuck signal (Current) | OFF or ON | OFF: No sliding roof switch stuck signal (Current)
ON: Sliding roof switch stuck signal (Current) |
- |
| Current Roof Close Switch Stuck ON | Sliding roof glass close switch stuck signal (Current) | OFF or ON | OFF: No sliding roof switch stuck signal (Current)
ON: Sliding roof switch stuck signal (Current) |
- |
| Current Shade Close Switch Stuck ON | Roof sunshade close switch stuck signal (Current) | OFF or ON | OFF: No roof sunshade switch stuck signal (Current)
ON: Roof sunshade switch stuck signal (Current) |
- |
| Current Shade Open Switch Stuck ON | Roof sunshade open switch stuck signal (Current) | OFF or ON | OFF: No roof sunshade switch stuck signal (Current)
ON: Roof sunshade switch stuck signal (Current) |
- |
| Past Roof Open Switch Stuck ON | Sliding roof glass open switch stuck signal (Past) | OFF or ON | OFF: No sliding roof switch stuck signal (Past)
ON: Sliding roof switch stuck signal (Past) |
- |
| Past Roof Close Switch Stuck ON | Sliding roof glass close switch stuck signal (Past) | OFF or ON | OFF: No sliding roof switch stuck signal (Past)
ON: Sliding roof switch stuck signal (Past) |
- |
| Past Shade Close Switch Stuck ON | Roof sunshade close switch stuck signal (Past) | OFF or ON | OFF: No roof sunshade switch stuck signal (Past)
ON: Roof sunshade switch stuck signal (Past) |
- |
| Past Shade Open Switch Stuck ON | Roof sunshade open switch stuck signal (Past) | OFF or ON | OFF: No roof sunshade switch stuck signal (Past)
ON: Roof sunshade switch stuck signal (Past) |
- |
| Current Vent Switch Stuck ON | Sliding roof glass tilt switch stuck signal (Current) | OFF or ON | OFF: No sliding roof switch stuck signal (Current)
ON: Sliding roof switch stuck signal (Current) |
- |
| Past Vent Switch Stuck ON | Sliding roof glass tilt switch stuck signal (Past) | OFF or ON | OFF: No sliding roof switch stuck signal (Past)
ON: Sliding roof switch stuck signal (Past) |
- |
| Suggestion Service Function | Availability of suggestion function* | OFF or ON | OFF: w/o Suggestion function
ON: w/ Suggestion function |
- |
| Number of Trouble Codes | Number of trouble codes | Min.: 0 to Max.: 255 | Number of DTCs is displayed | - |
*: Although this item is displayed on the GTS, it is not applicable to this vehicle.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Courtesy Switch Status | Front door courtesy light switch assembly RH signal | Close or Open | Close: Front door RH closed
Open: Front door RH open |
- |
| FL Door Courtesy Switch Status | Front door courtesy light switch assembly LH signal | Close or Open | Close: Front door LH closed
Open: Front door LH open |
- |
| Communication Slide Roof | Connection status between sliding roof ECU (sliding roof drive gear assembly [sliding roof]) and main body ECU (multiplex network body ECU) | STOP or OK | STOP: Communication stopped
OK: Normal communication |
- |
| Door Key P/W Up Function | Key-linked sliding roof close function | Disable or Enable | Customization status displayed | - |
| Door Key P/W Down Function | Key-linked sliding roof open function | Disable or Enable | Customization status displayed | - |
| P/W Up W/ Transmit Function | Wireless transmitter linked sliding roof close function | Disable or Enable | Customization status displayed | - |
| P/W Down W/ Transmit Function | Wireless transmitter linked sliding roof open function | Disable or Enable | Customization status displayed | - |
| Slide Roof Open Warning Function | Sliding roof open warning | Disable or Enable | Customization status displayed | - |
| Slide Roof Voice Control Function | Status of slide roof open/close linked voice recognition control | Disable or Enable | Customization status displayed | - |
ACTIVE TEST
Using the GTS, perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Slide Roof | Operate sliding motor | OFF / Opn/Dwn / Clos/Up | - |
| Front Sliding Sunshade | Operate sunshade motor | OFF / Open / Close | - |