DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Steering Angle Sensor / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wiper OFF Switch | Windshield wiper switch assembly (front wiper switch OFF position) condition | OFF or ON | OFF: Windshield wiper switch assembly (front wiper switch) not in OFF position
ON: Windshield wiper switch assembly (front wiper switch) in OFF position |
- |
| Wiper Auto/Int Switch | Windshield wiper switch assembly (INT position) condition | OFF or ON | OFF: Windshield wiper switch assembly not in INT position
ON: Windshield wiper switch assembly in INT position |
- |
| Wiper Lo Switch | Windshield wiper switch assembly (LO position) condition | OFF or ON | OFF: Windshield wiper switch assembly not in LO position
ON: Windshield wiper switch assembly in LO position |
- |
| Wiper Hi Switch | Windshield wiper switch assembly (HI position) condition | OFF or ON | OFF: Windshield wiper switch assembly not in HI position
ON: Windshield wiper switch assembly in HI position |
- |
| Wiper Mist Switch | Windshield wiper switch assembly (MIST position) condition | OFF or ON | OFF: Windshield wiper switch assembly not in MIST position
ON: Windshield wiper switch assembly in MIST position |
- |
| Washer Switch | Windshield wiper switch assembly (washer switch) condition | OFF or ON | OFF: Windshield wiper switch assembly (washer switch) in OFF position
ON: Windshield wiper switch assembly (washer switch) in ON position |
- |
| Rear Wiper INT Switch | Windshield wiper switch assembly (rear wiper switch INT position) condition | OFF or ON | OFF: Windshield wiper switch assembly (rear wiper switch) not in INT position
ON: Windshield wiper switch assembly (rear wiper switch) in INT position |
- |
| Rear Wiper ON Switch | Windshield wiper switch assembly (rear wiper switch ON position) condition | OFF or ON | OFF: Windshield wiper switch assembly (rear wiper switch) not in ON position
ON: Windshield wiper switch assembly (rear wiper switch) in ON position |
- |
| Rear Washer Switch | Windshield wiper switch assembly (rear washer switch) condition | OFF or ON | OFF: Windshield wiper switch assembly (rear washer switch) in OFF position
ON: Windshield wiper switch assembly (rear washer switch) in ON position |
- |
| Intermittent Time Volume (Shortest) | Intermittent time adjustment volume condition | OFF or ON | OFF: Windshield wiper switch assembly (intermittent time adjustment volume condition) not in P4 position
ON: Windshield wiper switch assembly (intermittent time adjustment volume condition) in P4 position |
- |
| Intermittent Time Volume (Shorter) | Intermittent time adjustment volume condition | OFF or ON | OFF: Windshield wiper switch assembly (intermittent time adjustment volume condition) not in P3 position
ON: Windshield wiper switch assembly (intermittent time adjustment volume condition) in P3 position |
- |
| Intermittent Time Volume (Longer) | Intermittent time adjustment volume condition | OFF or ON | OFF: Windshield wiper switch assembly (intermittent time adjustment volume condition) not in P2 position
ON: Windshield wiper switch assembly (intermittent time adjustment volume condition) in P2 position |
- |
| Intermittent Time Volume (Longest) | Intermittent time adjustment volume condition | OFF or ON | OFF: Windshield wiper switch assembly (intermittent time adjustment volume condition) not in P1 position
ON: Windshield wiper switch assembly (intermittent time adjustment volume condition) in P1 position |
- |
| Wiper Spec Info | Specification information | Unknown, Auto spec or Int spec | Unknown: Specification not stored
Auto spec: Automatic wiper control Int spec: Vehicle speed sensing intermittent time adjustment control |
- |
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Wiper Power Relay | Operates the windshield wiper relay (WIPER) | OFF or ON | - |
| Front Washer Relay | Operates the windshield wiper relay assembly | OFF or ON | - |
| Front Wiper Lo Operation | Function to operate the windshield wiper motor assembly in LO | OFF or ON | - |
| Front Wiper Hi Operation | Function to operate the windshield wiper motor assembly in HI | OFF or ON | - |
| Rear Washer Relay | Operates the windshield wiper relay assembly | OFF or ON | - |
| Rear Wiper Operation | Function to operate the rear wiper motor assembly | OFF or ON | - |
| Washer Nozzle Heater | Washer nozzle heater operation | OFF or ON | ·
This item can be used when the function is available ·
This item is not used when the function is unavailable |