The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear seat outer belt assembly removal/installation are shown below.
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the systems is used.
for HV Model:
Learning completes when vehicle is driven
| Effect/Inoperative Function when Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| Lane tracing assist system | Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. | ( 201910,999999,_58,_083101,_0401880,RM100000001JE9I,)
|
| Pre-collision system |
Learning completes when vehicle is operated normally
| Effect/Inoperative Function when Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| Power back door function | Fully close the back door by hand.
|
( 202304,999999,_59,_083093,_0584672,RM1000000029PGT,)
|
| Power door lock control system | If the back door is locked and therefore cannot be opened, it is necessary to unlock the back door using the door control switch, electrical key transmitter sub-assembly switch. | ( 202409,999999,_58,_083092,_0403003,RM100000002NS90,)
|
| Air conditioning system | After the ignition switch is turned to ON, the servo motor standard position is recognized | - |
for Gasoline Model:
Learning completes when vehicle is driven
| Effect/Inoperative Function when Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
| Stop and start system | Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). | ( 202409,999999,_51,_083056,_0402418,RM100000002NSFO,)
|
| Lane tracing assist system | Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. | ( 201910,999999,_58,_083101,_0401880,RM100000001JE9I,)
|
| Pre-collision system |
Learning completes when vehicle is operated normally
| Effect/Inoperative Function when Necessary Procedures are not Performed | Necessary Procedures | Link |
|---|---|---|
|
*: w/ Power back door system |
||
| Power back door function* | Fully close the back door by hand.
|
( 202304,999999,_59,_083093,_0584672,RM1000000029PGT,)
|
| Power door lock control system | If the back door is locked and therefore cannot be opened, it is necessary to unlock the back door using the door control switch, electrical key transmitter sub-assembly switch. | ( 202409,999999,_58,_083092,_0403003,RM100000002NS90,)
|
| Air conditioning system | After the ignition switch is turned to ON, the servo motor standard position is recognized | - |
Use the same procedure for the RH and LH sides.
The following procedure is for the LH side.
1. PRECAUTION
Be sure to read precaution thoroughly before servicing.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
58410B
2.REMOVE DECK BOARD ASSEMBLY
58416K
3.REMOVE REAR NO. 2 FLOOR BOARD
58417H
4.REMOVE REAR NO. 3 FLOOR BOARD
58386
5.REMOVE REAR FLOOR FINISH PLATE
65351A
6.REMOVE BATTERY HOLE COVER (for HV Model)
7.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
71940A
8.REMOVE REAR SEAT HEADREST ASSEMBLY
Remove the 2 rear seat headrest assemblies.
71960B
9.REMOVE REAR CENTER SEAT HEADREST ASSEMBLY
Remove the rear center seat headrest assembly.
10.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY
72693
11.REMOVE REAR SEAT CUSHION LOCK HOOK
12.REMOVE REAR SEATBACK ASSEMBLY LH
73350C
13.REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY (FLOOR ANCHOR)
14.REMOVE REAR SEATBACK ASSEMBLY RH
71304C
15.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH
71303C
16.REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
73706
17.REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH
73705
18.REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY RH
Use the same procedure described for the LH side.
67918E
19.REMOVE REAR DOOR SCUFF PLATE LH
67917C
20.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure described for the LH side.
58467H
21.REMOVE NO. 3 BATTERY SERVICE COVER BOARD (for HV Model)
58466J
22.REMOVE NO. 2 BATTERY SERVICE COVER BOARD (for HV Model)
58464D
23.REMOVE BATTERY SERVICE COVER BOARD (for HV Model)
58577E
24.REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE
62332C
25.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
Pull back the rear door opening trim weatherstrip LH so that the deck trim side panel assembly LH can be removed.
62331C
26.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure described for the LH side.
Pull back the rear door opening trim weatherstrip RH so that the deck trim side panel assembly RH can be removed.
62552F
27.REMOVE REAR SEAT SIDE GARNISH LH
62551F
28.REMOVE REAR SEAT SIDE GARNISH RH
Use the same procedure described for the LH side.
73708A
29.REMOVE TETHER ANCHOR BRACKET SET
58460D
30.REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY
64740E
31.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
64730J
32.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
62480A
33.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH
62470A
34.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH
Use the same procedure described for the LH side.
73370E
35.REMOVE REAR SEAT OUTER BELT ASSEMBLY LH (for SFTM Made)
Remove the bolt and the floor anchor of the rear seat outer belt assembly LH.
| *a | Locking Button |
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
|
Bolt |
|
Nut |
Remove the bolt and nut.
Detach the guide and remove the rear seat outer belt assembly LH.
Remove the bolt.
Detach the guide and remove the rear seat outer belt anchor bracket sub-assembly LH.
73370E
36.REMOVE REAR SEAT OUTER BELT ASSEMBLY LH (for GTMC Made)
Remove the bolt and the floor anchor of the rear seat outer belt assembly LH.
| *a | Locking Button |
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
|
Bolt |
|
Nut |
Remove the bolt and nut.
Detach the guide and remove the rear seat outer belt assembly LH.
Remove the bolt.
Detach the guide and remove the rear seat outer belt anchor bracket sub-assembly LH.
73360D
37.REMOVE REAR SEAT OUTER BELT ASSEMBLY RH (for SFTM Made)
Remove the bolt and the floor anchor of the rear seat outer belt assembly RH.
| *a | Locking Button |
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
|
Bolt |
|
Nut |
Remove the bolt and nut.
Detach the guide and remove the rear seat outer belt assembly RH.
Remove the bolt.
Detach the guide and remove the rear seat outer belt anchor bracket sub-assembly RH.
73360D
38.REMOVE REAR SEAT OUTER BELT ASSEMBLY RH (for GTMC Made)
Remove the bolt and floor anchor of the rear seat outer belt assembly RH.
| *a | Locking Button |
|
Remove in this Direction |
|
Protective Tape |
Using a thin-bladed screwdriver, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.
Tape the thin-bladed screwdriver tip before use.
|
Bolt |
|
Nut |
Remove the bolt and nut.
Detach the guide and remove the rear seat outer belt assembly RH.
Remove the bolt.
Detach the guide and remove the rear seat outer belt anchor bracket sub-assembly RH.