RM36D0EC _59 Vehicle Exterior _083111 EXTERIOR PANELS / TRIM _0400774 BLACK OUT TAPE(for Rear Door) A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE(for Rear Door)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during black out tape are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
·

Rear door glass sub-assembly LH

·

Rear door glass sub-assembly RH

·

Rear door glass run LH

·

Rear door glass run RH


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system


·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power back door function Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Power door lock control system If the back door is locked and therefore cannot be opened, it is necessary to unlock the back door using the door control switch, electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized -

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

When performing removal for the rear door belt moulding, disconnect the negative (-) auxiliary battery terminal after fully opening the rear door glass.



Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
·

Rear door glass sub-assembly LH

·

Rear door glass sub-assembly RH

·

Rear door glass run LH

·

Rear door glass run RH


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Wireless transmitter-linked function

·

Key-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane tracing assist system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system


·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*: w/ Power back door system

Power back door function* Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Power door lock control system If the back door is locked and therefore cannot be opened, it is necessary to unlock the back door using the door control switch, electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized -

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

When performing removal for the rear door belt moulding, disconnect the negative (-) auxiliary battery terminal after fully opening the rear door glass.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



a.

for M20D-FKS:

Click hereGeneral>MAINTENANCE>M20D-FKS BATTERY>REMOVAL


b.

for A25B-FXS:

Click hereGeneral>MAINTENANCE>A25B-FXS AUXILIARY BATTERY>REMOVAL


c.

for M20C-FKS:

Click hereGeneral>MAINTENANCE>M20C-FKS BATTERY>REMOVAL


d.

for A25D-FXS:

Click hereGeneral>MAINTENANCE>A25D-FXS AUXILIARY BATTERY>REMOVAL


e.

for A25F-FXS:

Click hereGeneral>MAINTENANCE>A25F-FXS AUXILIARY BATTERY (Production date from 2021/08)>REMOVAL


Hide 5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY

Hide 67408E 12.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY

Hide 75952A 17.REMOVE FRONT INNER BLACK OUT TAPE LH

HINT:

When removing the front inner black out tape LH, if it is difficult to remove, heat the adhesive of the front inner black out tape LH and rear door panel using a heat light.


Standard:
Item Temperature
Rear Door Panel 40 to 60°C (104 to 140°F)
Front Inner Black Out Tape LH 40 to 60°C (104 to 140°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat rear door panel and front inner black out tape LH excessively.


a.
B524069

Pull back on one of the ends of the front inner black out tape LH to remove it.

HINT:

When pulling on the front inner black out tape LH, pull it parallel to the rear door panel.



Hide 75938 18.REMOVE UPPER INNER BLACK OUT TAPE LH

HINT:

When removing the inner upper black out tape LH, if it is difficult to remove, heat the adhesive of the inner upper black out tape LH and rear door panel using a heat light.


Standard:
Item Temperature
Rear Door Panel 40 to 60°C (104 to 140°F)
Inner Upper Black Out Tape LH 40 to 60°C (104 to 140°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat rear door panel and inner upper black out tape LH excessively.


a.
B524070

Pull back on one of the ends of the inner upper black out tape LH to remove it.

HINT:

When pulling on the inner upper black out tape LH, pull it parallel to the rear door panel.



Hide 75954A 19.REMOVE REAR INNER BLACK OUT TAPE LH

HINT:

When removing the rear inner black out tape LH, if the double-sided tape is difficult to remove, heat the adhesive of the rear inner black out tape LH and rear door panel using a heat light.


Standard:
Item Temperature
Rear Door Panel 40 to 60°C (104 to 140°F)
Rear Inner Black Out Tape LH 40 to 60°C (104 to 140°F)


CAUTION:
E306500C35
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat rear door panel and rear inner black out tape LH excessively.


a.
B524071

Pull back on one of the ends of the rear inner black out tape LH to remove it.

HINT:

When pulling on the rear inner black out tape LH, pull it parallel to the rear door panel.