RM36D0EC _59 Vehicle Exterior _083111 EXTERIOR PANELS / TRIM _0400752 REAR BUMPER(for Type A) A

EXTERIOR PANELS / TRIM  REAR BUMPER(for Type A)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

If the bumper is damaged, there is a possibility that the installation area of the blind spot monitor sensor may be deformed and the blind spot monitor system may not operate correctly, so visually inspect the blind spot monitor sensor installation area (frame, stud bolt) to make sure it is not dented or bent.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SENSOR>ADJUSTMENT

·

If the visual inspection finds a problem, check the installation condition of the blind spot monitor sensor, and adjust the installation position of the blind spot monitor sensor as necessary.



PROCEDURE

Hide 1.INSTALL REAR BUMPER ASSEMBLY

a.
B524035C05
1.781,1.125 1.948,1.125 false 1.958,1.031 2.177,1.219 0.219,0.188 10 true *1
*1 Back Door Garnish Retainer
V113147

Install in this Direction


Attach the claw and back door garnish retainer to set the rear bumper assembly.

HINT:

Use the same procedure on the other side.



b.
B524101C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw.

HINT:

Use the same procedure on the other side.



c.
B523951

Install the 2 clips.


d.
B524188

Install the 2 screws.


e.
B524153

Install the clip.

HINT:

Use the same procedure on the other side.



f.
B555162

Connect the connector.


Hide 52599 2.INSTALL REAR BUMPER UPPER STOPPER

a.
B524152

Install the 2 rear bumper upper stoppers.


Hide 81497 4.INSTALL REAR COMBINATION LIGHT COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 75606A 5.INSTALL QUARTER OUTSIDE MOULDING SUB-ASSEMBLY LH

a.

except Off Road Package:

i.
B524156C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and clip to install the quarter outside moulding sub-assembly LH.


ii.
B524123C02
0,0 0,0 false
V100135

Screw
V100136

Clip


Install the screw.


iii.

Install the clip.


iv.

Remove the protective tape.



b.

for Off Road Package:

i.
B558155C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide and clip to install the quarter outside moulding sub-assembly LH.


ii.
B524124C02
0,0 0,0 false
V100135

Screw
V100136

Clip


Install the screw.


iii.

Install the clip.


iv.

Remove the protective tape.



Hide 75605A 6.INSTALL QUARTER OUTSIDE MOULDING SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 52592 7.INSTALL REAR BUMPER SIDE SEAL LH

a.
B524127C02
0,0 0,0 false
V100135

Clip
V100136

Screw


Install the rear bumper side seal LH with the 3 clips.


b.

Install the screw.


Hide 52591 8.INSTALL REAR BUMPER SIDE SEAL RH

a.
B523947C03
0,0 0,0 false
V100135

Clip
V100136

Screw


Install the rear bumper side seal RH with the 4 clips.


b.

Install the screw.


Hide 10. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL (w/ Hands Free Power Back Door)

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART