EXTERIOR PANELS / TRIM NAME PLATE INSTALLATION

Hide Display 75741E 1.INSTALL SYMBOL EMBLEM (for Type A)

HINT:: When installing the symbol emblem, heat the back door outside garnish sub-assembly and symbol emblem using a heat light.

Standard:

Item	Temperature
Back Door Outside Garnish Sub-assembly	20 to 30°C (68 to 86°F)
Symbol Emblem	20 to 30°C (68 to 86°F)

CAUTION:

2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b

*a	Heated Part
*b	Heat Light

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.

NOTICE:: Do not heat the back door outside garnish sub-assembly and symbol emblem excessively.

a.

Clean the surface of the back door outside garnish sub-assembly.

i.

Using a heat light, heat the back door outside garnish sub-assembly surface.

ii.

Remove any remaining double-sided tape from the back door outside garnish sub-assembly.

iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:: ·

Installing the symbol emblem with any double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

b.

Using a heat light, heat the back door outside garnish sub-assembly and a new symbol emblem.

c.

Remove the release paper from the symbol emblem.

NOTICE:: After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.

d.

Align the boss positions and install the symbol emblem.

NOTICE:: The application strength of the symbol emblem will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

HINT:: Apply pressure so that it does not lift up from the back door outside garnish sub-assembly.

i.

2.531,3.781 2.823,3.781 false 0.521,3.469 0.813,3.469 false 0.333,3.375 0.646,3.573 0.313,0.198 10 false *a 2.875,3.688 3.115,3.885 0.24,0.198 10 false *a

*a	Boss Position

for Gasoline Model:

ii.

0.5,3.469 0.813,3.469 false 2.531,3.771 2.844,3.771 false 0.323,3.375 0.635,3.573 0.313,0.198 10 false *a 2.896,3.667 3.208,3.865 0.313,0.198 10 false *a

*a	Boss Position

for HV Model:

Hide Display 75741E 2.INSTALL SYMBOL EMBLEM (for Type B)

HINT:: When installing the symbol emblem, heat the back door outside garnish sub-assembly and symbol emblem using a heat light.

Standard:

Item	Temperature
Back Door Outside Garnish Sub-assembly	20 to 30°C (68 to 86°F)
Symbol Emblem	20 to 30°C (68 to 86°F)

CAUTION:

2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b

*a	Heated Part
*b	Heat Light

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.

NOTICE:: Do not heat the back door outside garnish sub-assembly and symbol emblem excessively.

a.

Clean the surface of the back door outside garnish sub-assembly.

i.

Using a heat light, heat the back door outside garnish sub-assembly surface.

ii.

Remove any remaining double-sided tape from the back door outside garnish sub-assembly.

iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:: ·

Installing the symbol emblem with any double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

b.

Using a heat light, heat the back door outside garnish sub-assembly and the new symbol emblem.

c.

Remove the release paper from the symbol emblem.

NOTICE:: After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.

d.

Align the boss positions and install the symbol emblem.

NOTICE:: The application strength of the symbol emblem will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

HINT:: Apply pressure so that it does not lift up from the back door outside garnish sub-assembly.

i.

0.49,3.333 0.76,3.333 false 2.615,3.667 2.885,3.667 false 0.313,3.26 0.469,3.458 0.156,0.198 10 false *a 2.906,3.573 3.063,3.771 0.156,0.198 10 false *a

*a	Boss Position

for Gasoline Model:

ii.

0.458,3.323 0.74,3.323 false 2.615,3.677 2.896,3.677 false 0.302,3.229 0.615,3.427 0.313,0.198 10 false *a 2.938,3.563 3.25,3.76 0.313,0.198 10 false *a

*a	Boss Position

for HV Model:

Hide Display 75441E 3.INSTALL BACK DOOR NO. 1 NAME PLATE

HINT:: When installing the back door No. 1 name plate, heat the back door panel and back door No. 1 name plate using a heat light.

Standard:

Item	Temperature
Back Door Panel	40 to 60°C (104 to 140°F)
Back Door No. 1 Name Plate	20 to 30°C (68 to 86°F)

CAUTION:

2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b

*a	Heated Part
*b	Heat Light

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.

NOTICE:: Do not heat the back door panel and back door No. 1 name plate excessively.

a.

Clean the surface of the back door panel.

i.

Using a heat light, heat the back door panel surface.

ii.

Remove any remaining double-sided tape from the back door panel.

iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:: ·

Installing the back door No. 1 name plate with any double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

b.

Using a heat light, heat the back door panel and the new back door No. 1 name plate.

c.

Remove the release paper from the back door No. 1 name plate.

NOTICE:: After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.

d.

Install the back door No. 1 name plate as shown in the illustration.

NOTICE:: The application strength of the back door No. 1 name plate will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

HINT:: Apply pressure so that it does not lift up from the back door panel.

i.

for Type A:

4.375,0.885 4.688,0.74 true 4.865,2.625 5.26,2.219 true 4.385,0.188 4.583,0.375 0.198,0.188 10 true *a 5.292,0.5 5.438,0.677 0.146,0.177 10 true A 5.354,1.438 5.49,1.583 0.135,0.146 10 true B 4.344,1.719 4.49,1.875 0.146,0.156 10 false C 4.823,0.802 4.969,0.958 0.146,0.156 10 true D 4.198,0.844 4.406,1.021 0.208,0.177 10 false *b 4.74,2.615 4.958,2.792 0.219,0.177 10 false *c 4.813,1.75 4.948,1.896 0.135,0.146 10 true E 6.083,1.604 6.219,1.75 0.135,0.146 10 true F 6.344,1.469 6.479,1.615 0.135,0.146 10 true G

*a	Reference Values	*b	Back Door Edge Line
*c	Back Door Lower Outside Garnish Sub-assembly Upper Side Edge	-	-

Standard Measurement:

Area	Measurement	Area	Measurement
A	170.7 mm (6.72 in.)	B	164.5 mm (6.48 in.)
C	115.2 mm (4.54 in.)	D	20.1 mm (0.791 in.)
E	120.8 mm (4.76 in.)	F	118.7 mm (4.67 in.)
G	147.9 mm (5.82 in.)	-	-

ii.

for Type B:

4.615,2.292 4.833,2.021 false 4.865,2.594 4.958,2.156 true 4.458,2.302 4.771,2.5 0.313,0.198 10 false *b 4.75,2.615 5.063,2.813 0.313,0.198 10 false *c 5,0.208 5.104,0.354 0.104,0.146 10 true A 5,0.396 5.104,0.542 0.104,0.146 10 true B 4.271,1.594 4.375,1.74 0.104,0.146 10 true C 4.708,1.594 4.813,1.74 0.104,0.146 10 true D 5.292,1.604 5.396,1.75 0.104,0.146 10 true E 5.635,1.625 5.74,1.771 0.104,0.146 10 true F 6.302,1.646 6.406,1.792 0.104,0.146 10 true G 4.094,0.198 4.26,0.385 0.167,0.188 10 true *a

*a	Reference Values	*b	Back Door Edge Line
*c	Back Door Lower Outside Garnish Sub-assembly Upper Side Edge	-	-

Standard Measurement:

Area	Measurement	Area	Measurement
A	193.9 mm (7.63 in.)	B	185.9 mm (7.32 in.)
C	93.7 mm (3.69 in.)	D	8.6 mm (0.34 in.)
E	164.6 mm (6.48 in.)	F	158 mm (6.22 in.)
G	183.2 mm (7.21 in.)	-	-

Hide Display 75445A 4.INSTALL BACK DOOR NO. 5 NAME PLATE

HINT:: When installing the back door No. 5 name plate, heat the back door panel and back door No. 5 name plate using a heat light.

Standard:

Item	Temperature
Back Door Panel	40 to 60°C (104 to 140°F)
Back Door No. 5 Name Plate	20 to 30°C (68 to 86°F)

CAUTION:

2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b

*a	Heated Part
*b	Heat Light

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.

NOTICE:: Do not heat the back door panel and back door No. 5 name plate excessively.

a.

Clean the surface of the back door panel.

i.

Using a heat light, heat the back door panel surface.

ii.

Remove any remaining double-sided tape from the back door panel.

iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:: ·

Installing the back door No. 5 name plate with any double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

b.

Using a heat light, heat the back door panel and the new back door No. 5 name plate.

c.

Remove the release paper from the back door No. 5 name plate.

NOTICE:: After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.

d.

Install the back door No. 5 name plate as shown in the illustration.

NOTICE:: The application strength of the back door No. 5 name plate will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

HINT:: Apply pressure so that it does not lift up from the back door panel.

i.

for Type A:

4.313,0.51 4.073,0.385 false 6.573,2.073 6.052,1.906 true 6.198,0.26 6.396,0.458 0.198,0.198 10 true *a 4.469,0.615 4.615,0.792 0.146,0.177 10 true A 5.094,1.656 5.229,1.802 0.135,0.146 10 true B 5.802,1.656 5.948,1.813 0.146,0.156 10 true C 4.479,1.51 4.615,1.688 0.135,0.177 10 true D 3.896,0.292 4.052,0.469 0.156,0.177 10 true *b 6.635,2.052 6.948,2.25 0.313,0.198 10 false *c

*a	Reference Values	*b	Back Door Edge Line
*c	Back Door Lower Outside Garnish Sub-assembly Upper Side Edge	-	-

Standard Measurement:

Area	Measurement	Area	Measurement
A	36.3 mm (1.43 in.)	B	93.4 mm (3.68 in.)
C	91.8 mm (3.61 in.)	D	30.5 mm (1.20 in.)

ii.

for Type B:

4.688,0.417 4.406,0.354 false 6.552,2.271 6.25,2.125 true 6.042,0.26 6.229,0.458 0.188,0.198 10 true *a 4.24,0.271 4.427,0.469 0.188,0.198 10 true *b 6.583,2.198 6.771,2.396 0.188,0.198 10 true *c 4.75,0.5 4.865,0.656 0.115,0.156 10 true A 5.354,1.844 5.469,2 0.115,0.156 10 true B 5.99,1.833 6.104,1.99 0.115,0.156 10 true C 4.76,1.552 4.875,1.708 0.115,0.156 10 true D

*a	Reference Values	*b	Back Door Edge Line
*c	Back Door Lower Outside Garnish Sub-assembly Upper Side Edge	-	-

Standard Measurement:

Area	Measurement	Area	Measurement
A	31.1 mm (1.22 in.)	B	132 mm (5.20 in.)
C	129.3 mm (5.09 in.)	D	28.8 mm (1.13 in.)

Hide Display 75443 5.INSTALL BACK DOOR NO. 3 NAME PLATE

HINT:: When installing the back door No. 3 name plate, heat the back door panel and back door No. 3 name plate using a heat light.

Standard:

Item	Temperature
Back Door Panel	40 to 60°C (104 to 140°F)
Back Door No. 3 Name Plate	20 to 30°C (68 to 86°F)

CAUTION:

2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b

*a	Heated Part
*b	Heat Light

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.

NOTICE:: Do not heat the back door panel and back door No. 3 name plate excessively.

a.

Clean the surface of the back door panel.

i.

Using a heat light, heat the back door panel surface.

ii.

Remove any remaining double-sided tape from the back door panel.

iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:: ·

Installing the back door No. 3 name plate with any double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

b.

Using a heat light, heat the back door panel and the new back door No. 3 name plate.

c.

Remove the release paper from the back door No. 3 name plate.

NOTICE:: After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.

d.

Install the back door No. 3 name plate as shown in the illustration.

NOTICE:: The application strength of the back door No. 3 name plate will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

HINT:: Apply pressure so that it does not lift up from the back door panel.

i.

for Type A:

6.125,0.323 6.417,0.271 false 3.833,1.552 4,1.552 4,1.552 4.156,1.854 true 4.198,0.292 4.375,0.479 0.177,0.188 10 true *a 6.271,0.479 6.417,0.656 0.146,0.177 10 true A 6.271,1.01 6.406,1.156 0.135,0.146 10 true B 5.531,1.333 5.677,1.49 0.146,0.156 10 true C 5.438,1.625 5.573,1.802 0.135,0.177 10 true D 4.313,1.625 4.458,1.813 0.146,0.188 10 true E 6.458,0.167 6.771,0.365 0.313,0.198 10 false *b 3.646,1.469 3.958,1.667 0.313,0.198 10 false *c

*a	Reference Values	*b	Back Door Edge Line
*c	Back Door Lower Outside Garnish Sub-assembly Upper Side Edge	-	-

Standard Measurement:

Area	Measurement	Area	Measurement
A	16.7 mm (0.657 in.)	B	24.1 mm (0.949 in.)
C	172.6 mm (6.80 in.)	D	122.7 mm (4.83 in.)
E	120.7 mm (4.75 in.)	-	-

ii.

for Type B:

5.948,2.073 6.198,2.333 false 5.344,2.146 5.438,2.531 true 4.448,0.281 4.635,0.479 0.188,0.198 10 true *a 6.219,2.333 6.406,2.531 0.188,0.198 10 true *b 5.375,2.531 5.563,2.729 0.188,0.198 10 true *c 5.594,0.24 5.698,0.396 0.104,0.156 10 true A 5.625,0.438 5.719,0.583 0.094,0.146 10 true B 6.385,1.667 6.51,1.833 0.125,0.167 10 true C 5.99,1.667 6.115,1.833 0.125,0.167 10 true D 5.51,1.635 5.635,1.802 0.125,0.167 10 true E 5.115,1.635 5.24,1.802 0.125,0.167 10 true F 4.24,1.688 4.365,1.854 0.125,0.167 10 true G

*a	Reference Values	*b	Back Door Edge Line
*c	Back Door Lower Outside Garnish Sub-assembly Upper Side Edge	-	-

Standard Measurement:

Area	Measurement	Area	Measurement
A	189.2 mm (7.45 in.)	B	185 mm (7.28 in.)
C	117 mm (4.61 in.)	D	13.2 mm (0.520 in.)
E	165.8 mm (6.53 in.)	F	158.3 mm (6.23 in.)
G	183.9 mm (7.24 in.)	-	-

Hide Display 75444A 6.INSTALL BACK DOOR NO. 4 NAME PLATE

HINT:: When installing the back door No. 4 name plate, heat the back door panel and back door No. 4 name plate using a heat light.

Standard:

Item	Temperature
Back Door Panel	40 to 60°C (104 to 140°F)
Back Door No. 4 Name Plate	20 to 30°C (68 to 86°F)

CAUTION:

2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b

*a	Heated Part
*b	Heat Light

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.

NOTICE:: Do not heat the back door panel and back door No. 4 name plate excessively.

a.

Clean the surface of the back door panel.

i.

Using a heat light, heat the back door panel surface.

ii.

Remove any remaining double-sided tape from the back door panel.

iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:: ·

Installing the back door No. 4 name plate with any double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

b.

Using a heat light, heat the back door panel and the new back door No. 4 name plate.

c.

Remove the release paper from the back door No. 4 name plate.

NOTICE:: After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.

d.

Install the back door No. 4 name plate as shown in the illustration.

NOTICE:: The application strength of the back door No. 4 name plate will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

HINT:: Apply pressure so that it does not lift up from the back door panel.

i.

for Type A:

6.24,0.365 6.51,0.469 false 4.094,2.083 4.333,1.917 true 4.281,0.271 4.458,0.458 0.177,0.188 10 true *a 5.927,0.521 6.073,0.698 0.146,0.177 10 true A 5.646,1.49 5.781,1.635 0.135,0.146 10 true B 6.365,1.802 6.51,1.958 0.146,0.156 10 true C 4.813,1.708 4.948,1.885 0.135,0.177 10 true D 6.573,0.417 6.885,0.615 0.313,0.198 10 false *b 3.927,2.073 4.24,2.271 0.313,0.198 10 false *c

*a	Reference Values	*b	Back Door Edge Line
*c	Back Door Lower Outside Garnish Sub-assembly Upper Side Edge	-	-

Standard Measurement:

Area	Measurement	Area	Measurement
A	58.8 mm (2.31 in.)	B	119 mm (4.69 in.)
C	93.6 mm (3.69 in.)	D	91.2 mm (3.59 in.)

6.208,0.281 6.458,0.354 false 3.958,2.031 4.177,1.865 true 4.219,0.292 4.385,0.469 0.167,0.177 10 true *a 5.979,0.271 6.125,0.448 0.146,0.177 10 true A 6.25,1.302 6.385,1.448 0.135,0.146 10 true B 5.438,1.635 5.583,1.792 0.146,0.156 10 true C 4.479,1.625 4.615,1.802 0.135,0.177 10 true D 6.49,0.281 6.802,0.479 0.313,0.198 10 false *b 3.823,2.01 4.135,2.208 0.313,0.198 10 false *c

*a	Reference Values	*b	Back Door Edge Line
*c	Back Door Lower Outside Garnish Sub-assembly Upper Side Edge	-	-

Standard Measurement:

Area	Measurement	Area	Measurement
A	33.8 mm (1.33 in.)	B	37.1 mm (1.46 in.)
C	92.9 mm (3.66 in.)	D	91.5 mm (3.60 in.)

ii.

for Type B:

6.073,0.51 6.573,0.417 false 4.156,2.344 4.49,2.135 true 4.458,0.344 4.604,0.531 0.146,0.188 10 true *a 6.615,0.323 6.76,0.51 0.146,0.188 10 true *b 4.021,2.313 4.167,2.5 0.146,0.188 10 true *c 5.813,0.594 5.927,0.76 0.115,0.167 10 true A 5.823,0.854 5.938,1.021 0.115,0.167 10 true B 6.031,1.854 6.146,2.021 0.115,0.167 10 true C 4.792,1.854 4.906,2.021 0.115,0.167 10 true D

*a	Reference Values	*b	Back Door Edge Line
*c	Back Door Lower Outside Garnish Sub-assembly Upper Side Edge	-	-

Standard Measurement:

Area	Measurement	Area	Measurement
A	117.5 mm (4.63 in.)	B	58 mm (2.28 in.)
C	129.7 mm (5.11 in.)	D	128.1 mm (5.04 in.)

6.073,0.479 6.333,0.365 false 4.083,2.271 4.531,2.135 true 4.427,0.313 4.656,0.5 0.229,0.188 10 true *a 3.896,2.208 4.229,2.396 0.333,0.188 10 false *c 6.406,0.271 6.75,0.479 0.344,0.208 10 false *b 5.927,0.625 6.042,0.781 0.115,0.156 10 true A 5.896,1.604 6.01,1.76 0.115,0.156 10 true B 5.344,1.833 5.458,1.99 0.115,0.156 10 true C 4.563,1.833 4.677,1.99 0.115,0.156 10 true D

*a	Reference Values	*b	Back Door Edge Line
*c	Back Door Lower Outside Garnish Sub-assembly Upper Side Edge	-	-

Standard Measurement:

Area	Measurement	Area	Measurement
A	28.6 mm (1.13 in.)	B	33 mm (1.30 in.)
C	129.1 mm (5.08 in.)	D	129.3 mm (5.09 in.)

Hide Display 75362 7.INSTALL FRONT FENDER NO. 2 NAME PLATE

HINT:: When installing the front fender No. 2 name plate, heat the fender panel and front fender No. 2 name plate using a heat light.

Standard:

Item	Temperature
Fender Panel	40 to 60°C (104 to 140°F)
Front Fender No. 2 Name Plate	20 to 30°C (68 to 86°F)

CAUTION:

2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b

*a	Heated Part
*b	Heat Light

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.

NOTICE:: Do not heat the fender panel and front fender No. 2 name plate excessively.

a.

Clean the surface of the fender panel.

i.

Using a heat light, heat the fender panel surface.

ii.

Remove any remaining double-sided tape from the fender panel.

iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:: ·

Installing the front fender No. 2 name plate with any double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

b.

Using a heat light, heat the fender panel and the new front fender No. 2 name plate.

c.

Remove the release paper from the front fender No. 2 name plate.

NOTICE:: After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.

d.

Install the front fender No. 2 name plate as shown in the illustration.

3.813,1.531 4.031,1.531 true 6.229,0.698 6.458,0.698 true 3.792,0.24 3.969,0.427 0.177,0.188 10 true *a 5.323,2.115 5.448,2.292 0.125,0.177 10 true A 4.365,1.76 4.5,1.906 0.135,0.146 10 true B 4.688,1.417 4.833,1.573 0.146,0.156 10 true D 5.615,1.385 5.75,1.563 0.135,0.177 10 true E 5.958,1.76 6.094,1.906 0.135,0.146 10 true C 3.646,1.448 3.958,1.646 0.313,0.198 10 false *b 6.51,0.604 6.823,0.802 0.313,0.198 10 false *c 5.99,1.313 6.125,1.49 0.135,0.177 10 true F 5.979,0.688 6.115,0.865 0.135,0.177 10 true G

*a	Reference Values	*b	Lower Side Baseline
*c	Front Fender Edge Line	-	-

Standard Measurement:

Area	Measurement	Area	Measurement
A	200 mm (7.87 in.)	B	18.5 mm (0.726 in.)
C	35.2 mm (1.39 in.)	D	43.2 mm (1.70 in.)
E	56.8 mm (2.23 in.)	F	37.4 mm (1.47 in.)
G	41.2 mm (1.62 in.)	-	-

NOTICE:: The application strength of the front fender No. 2 name plate will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

HINT:: Apply pressure so that it does not lift up from the fender panel.

Hide Display 75361A 8.INSTALL FRONT FENDER NO. 1 NAME PLATE

HINT:: When installing the front fender No. 1 name plate, heat the fender panel and front fender No. 1 name plate using a heat light.

Standard:

Item	Temperature
Fender Panel	40 to 60°C (104 to 140°F)
Front Fender No. 1 Name Plate	20 to 30°C (68 to 86°F)

CAUTION:

2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b

*a	Heated Part
*b	Heat Light

·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.

NOTICE:: Do not heat the fender panel and front fender No. 1 name plate excessively.

a.

Clean the surface of the fender panel.

i.

Using a heat light, heat the fender panel surface.

ii.

Remove any remaining double-sided tape from the fender panel.

iii.

Wipe off any tape adhesive residue with cleaner.

NOTICE:: ·

Installing the front fender No. 1 name plate with any double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.

b.

Using a heat light, heat the fender panel and the new front fender No. 1 name plate.

c.

Remove the release paper from the front fender No. 1 name plate.

NOTICE:: After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.

d.

Install the front fender No. 1 name plate as shown in the illustration.

6.51,1.51 6.292,1.51 true 4.313,0.802 4.063,0.802 true 3.802,0.24 3.99,0.427 0.188,0.188 10 true *a 5.073,2.01 5.219,2.188 0.146,0.177 10 true A 6.125,1.698 6.323,1.844 0.198,0.146 10 true B 4.438,1.698 4.583,1.854 0.146,0.156 10 true C 5.719,1.365 5.865,1.51 0.146,0.146 10 true D 4.792,1.313 4.927,1.49 0.135,0.177 10 true E 6.573,1.427 6.781,1.615 0.208,0.188 10 false *b 3.844,0.719 4.052,0.906 0.208,0.188 10 false *c 4.458,1.24 4.594,1.417 0.135,0.177 10 true F 4.448,0.646 4.583,0.823 0.135,0.177 10 true G

*a	Reference Values	*b	Lower Side Baseline
*c	Front Fender Edge Line	-	-

Standard Measurement:

Area	Measurement	Area	Measurement
A	200 mm (7.87 in.)	B	20.7 mm (0.815 in.)
C	32.7 mm (1.29 in.)	D	43.5 mm (1.71 in.)
E	57.9 mm (2.28 in.)	F	34.9 mm (1.37 in.)
G	38.0 mm (1.50 in.)	-	-

NOTICE:: The application strength of the front fender No. 1 name plate will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

HINT:: Apply pressure so that it does not lift up from the fender panel.

EXTERIOR PANELS / TRIM NAME PLATE INSTALLATION

PROCEDURE