RM36D0EC _58 Vehicle Interior _083095 LIGHTING (INT) _0400584 LIGHTING SYSTEM D

LIGHTING (INT) LIGHTING SYSTEM OPERATION CHECK

INSPECT ILLUMINATED ENTRY SYSTEM OPERATION

NOTICE:: Perform this inspection with the customize parameters at the initial settings.; Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>CUSTOMIZE PARAMETERS202304,202405,_58,_083095,_0400584,RM1000000029DD3,202405,202409,_58,_083095,_0400584,RM100000002JO93,202409,999999,_58,_083095,_0400584,RM100000002NSNF,

HINT:

Perform this inspection with the door switch of the map light assembly and No. 1 room light assembly on.

Lights Controlled by Illuminated Entry System
Control	Condition	Lights that Operate
1: w/ Smart Entry and Start System 2: w/o Smart Entry and Start System 3: w/ Footwell Light 4: w/ Tray Light
Actuation Area-linked*1	With the ignition switch off and all of the doors closed and locked, enter an exterior detection area while carrying an electrical key transmitter and check that the lights that operate turn on for approximately 15 seconds and then turn off.	· Map light assembly · No. 1 room light assembly · No. 1 interior illumination light assembly LH (footwell light)3 · No. 1 interior illumination light assembly RH (footwell light)3 · Console box illumination light assembly (cup holder light)3 · No. 1 interior illumination light assembly (driver side tray light)4 · Interior illumination light assembly (front passenger side tray light)4 · No. 1 interior illumination light assembly (center tray light)4
Door Lock/Unlock-linked	With the ignition switch off and all of the doors closed and locked, unlock either front door using an unlock operation (key-linked, wireless or entry unlock operation) and check that the lights that operate turn on for 15 seconds and then turn off.	· Map light assembly · No. 1 room light assembly · No. 1 interior illumination light assembly LH (footwell light)3 · No. 1 interior illumination light assembly RH (footwell light)3 · Console box illumination light assembly (cup holder light)3 · No. 1 interior illumination light assembly (driver side tray light)4 · Interior illumination light assembly (front passenger side tray light)4 · No. 1 interior illumination light assembly (center tray light)4
Door Open/Close-linked	With the ignition switch off and all of the doors closed, open either front door and check that the lights that operate turn ON. While the lights that operate are on, close all of the doors and check that the lights that operate turn off after approximately 15 seconds.	· Map light assembly · No. 1 room light assembly · No. 1 interior illumination light assembly LH (footwell light)3 · No. 1 interior illumination light assembly RH (footwell light)3 · Console box illumination light assembly (cup holder light)3 · No. 1 interior illumination light assembly (driver side tray light)4 · Interior illumination light assembly (front passenger side tray light)4 · No. 1 interior illumination light assembly (center tray light)4
	With the ignition switch off and all the doors closed, open the front door and check that the blinking interval for the lights listed on the right slows down. After this, check that the blinking interval for the lights listed on the right quickens when the brake pedal is depressed.	Push start switch illumination
	With the ignition switch ON, open either front door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off.	· Map light assembly · No. 1 room light assembly
Push Start Switch-linked*1	Turn the ignition switch from ACC or ON to off and check that the lights that operate turn on for approximately 15 seconds and then turn off.	· Map light assembly · No. 1 room light assembly · No. 1 interior illumination light assembly LH (footwell light)3 · No. 1 interior illumination light assembly RH (footwell light)3 · Console box illumination light assembly (cup holder light)3 · No. 1 interior illumination light assembly (driver side tray light)4 · Interior illumination light assembly (front passenger side tray light)4 · No. 1 interior illumination light assembly (center tray light)4
	Turn the ignition switch ACC or ON and check that the lights that operate turn on.	· Map light assembly · No. 1 room light assembly · No. 1 interior illumination light assembly LH (footwell light)3 · No. 1 interior illumination light assembly RH (footwell light)3 · Console box illumination light assembly (cup holder light)3 · No. 1 interior illumination light assembly (driver side tray light)4 · Interior illumination light assembly (front passenger side tray light)4 · No. 1 interior illumination light assembly (center tray light)4
	Turn the ignition switch from ACC or ON to off and check that the lights that operate turn off.	· Map light assembly · No. 1 room light assembly · No. 1 interior illumination light assembly LH (footwell light)3 · No. 1 interior illumination light assembly RH (footwell light)3 · Console box illumination light assembly (cup holder light)3 · No. 1 interior illumination light assembly (driver side tray light)4 · Interior illumination light assembly (front passenger side tray light)4 · No. 1 interior illumination light assembly (center tray light)4
	Check that the blinking interval for the lights listed on the right slows down when the ignition switch is turned from ACC or ON to off.	Push start switch illumination
Ignition Switch-linked*2	Turn the ignition switch from ACC or ON to off and check that the lights that operate turn on for approximately 15 seconds and then turn off.	· Map light assembly · No. 1 room light assembly · No. 1 interior illumination light assembly LH (footwell light)3 · No. 1 interior illumination light assembly RH (footwell light)3 · Console box illumination light assembly (cup holder light)3 · No. 1 interior illumination light assembly (driver side tray light)4 · Interior illumination light assembly (front passenger side tray light)4 · No. 1 interior illumination light assembly (center tray light)4
Vehicle Speed-linked	With the ignition switch turned to ACC or ON, release the parking brake, drive the vehicle at least 3 km/h (1.9 mph), and check that the lights dim. While the lights are dim, stop the vehicle, apply the parking brake, and check that the lights return to full brightness.	· Map light assembly · No. 1 room light assembly · No. 1 interior illumination light assembly LH (footwell light)3 · No. 1 interior illumination light assembly RH (footwell light)3 · Console box illumination light assembly (cup holder light)3 · No. 1 interior illumination light assembly (driver side tray light)4 · Interior illumination light assembly (front passenger side tray light)4 · No. 1 interior illumination light assembly (center tray light)4

INSPECT BATTERY SAVING CONTROL OPERATION

The operations and conditions of this control are described below.

Control	Condition	Lights that Operate
1: w/ Smart Entry and Start System 2: w/ Footwell Light *3: w/ Tray Light
Basic operation	When 20 minutes elapse after the ignition switch is turned from ACC or IG to off and the lights that operate remain on, the lights are turned off. HINT: Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off. · The ignition switch is turned to ACC or IG. · Any door is opened and closed. · The back door is opened and closed. · Any door is unlocked. · The key enters any exterior actuation area.	· Push start switch illumination1 · No. 1 interior illumination light assembly LH (footwell light)2 · No. 1 interior illumination light assembly RH (footwell light)2 · Console box illumination light assembly (cup holder light)2 · No. 1 interior illumination light assembly (driver side tray light)3 · Interior illumination light assembly (front passenger side tray light)3 · No. 1 interior illumination light assembly (center tray light)*3
Interior light auto cut operation	When 20 minutes elapse after the ignition switch is turned from on (ACC or IG) to off and the lights that operate remain on, the lights are turned off. HINT: Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off. · The ignition switch is turned to ACC or IG.	· Map light assembly · No. 1 room light assembly · Vanity light assembly