RM36D0EC _59 Vehicle Exterior _083093 DOOR / HATCH _0403697 POWER BACK DOOR DRIVE UNIT A

DOOR / HATCH POWER BACK DOOR DRIVE UNIT REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the power back door unit assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure	Necessary Procedures	Effect/Inoperative Function when Necessary Procedures are not Performed	Link
Power back door unit assembly set	Reset back door close position	Power back door system	(202304,999999,_59,_083093,_0584672,RM1000000029PGT,)

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure	Necessary Procedures	Effect/Inoperative Function when Necessary Procedures are not Performed	Link
Power back door unit assembly set	Reset back door close position	Power back door system	(202304,999999,_59,_083093,_0584672,RM1000000029PGT,)

HINT:: ·

Use the same procedure for the RH and LH sides.

·

The procedure below is for the LH side.

PROCEDURE

Hide Display 67939B 1.REMOVE BACK DOOR CENTER GARNISH

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR>DISASSEMBLY202304,999999,_59,_083093,_0403691,RM1000000029SAX_01_0010,

Hide Display 67938A 2.REMOVE BACK DOOR SIDE GARNISH LH

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR>DISASSEMBLY202304,999999,_59,_083093,_0403691,RM1000000029SAX_01_0021,

Hide Display 67937B 3.REMOVE BACK DOOR SIDE GARNISH RH

HINT:: Use the same procedure described for the LH side.

Hide Display 67199 4.REMOVE BACK DOOR HANDLE COVER

HINT:: Use the same procedure for the RH and LH sides.; Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR>DISASSEMBLY202304,999999,_59,_083093,_0403691,RM1000000029SAX_01_0034,

Hide Display 67750 5.REMOVE BACK DOOR TRIM BOARD ASSEMBLY

Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR>DISASSEMBLY202304,999999,_59,_083093,_0403691,RM1000000029SAX_01_0048,

Hide Display 6.REMOVE POWER BACK DOOR UNIT ASSEMBLY LH

CAUTION:: ·

Do not perform work if the back door is not securely supported.

·

The back door could fall, resulting in injury.

0,0 0,0 false

	Remove in this Direction
	Grommet
	Connector

Disconnect the connector.

Disconnect the grommet and pull out the power back door unit assembly LH harness as shown in the illustration.

0,0 0,0 false

Protective Tape

Using a screwdriver with its tip wrapped with protective tape, slightly raise the 2 stop rings as shown in the illustration.

Detach the 2 ball joints to remove the power back door unit assembly LH.

NOTICE:: ·

Remove the power back door unit assembly LH while supporting the back door by hand.

·

Remove the back door stay assembly while supporting the back door stay assembly by hand.

Hide Display 68946 7.REMOVE BACK DOOR UPPER DAMPER STAY BRACKET LH

Remove the 2 bolts and back door upper damper stay bracket LH.

Hide Display 68948 8.REMOVE BACK DOOR LOWER DAMPER STAY BRACKET LH

Remove the 2 bolts and back door lower damper stay bracket LH with back door stay stopper.

Hide Display 68984 9.REMOVE BACK DOOR STAY STOPPER

Detach the claw and remove the back door stay stopper from the back door lower damper stay bracket LH.